Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ MPgMB Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Work material Mild Steel, Carbon steel, Alloy steel, Prehardened steel, Hardened steel ( 45HRC) AIS11050, AISI P21, AISI H13 Hardened steel (45 55HRC) AISI 420, AISI H13 Copper, Copper alloys R 18 RE (mm) 0 15' 0>15' Depth f cut ip (mm) Pick feed Pi M 0 15' off Depth of cut

ir Depth of cut mm Pick feed I (mm) RenoMitn (niir'l Feed rate (mu/mill) Reiokition niir'l Feed rate Mn Revolution (miir1) Feed rale fynnMn Revolution (miir'J Feel rate (mmlmin RevtMin (mir'l Feed rate (mmlmii) Revolution (miir'l Feed rail (mmlmin) R0.1 40000 300 40000 250 0.003 0.02 40000 300 40000 250 0.003 0.02 40000 300 40000 250 0.003 0.02 R0.15 40000 500 40000 350 0.007 0.03 40000 500 40000 350 0.007 0.03 40000 500 40000 350 0.007 0.03 R0.2 40000 1600 40000 1200 0.02 0.04 40000 1300 40000 950 0.015 0.04 40000 1300 40000 950 0.015 0.04 R0.25 40000 2400 40000 1400 0.025 0.05 40000 1900 40000 1100 0.02 0.05 40000 1900 40000 1100 0.02 0.05 R0.3 40000 3200 40000 1600 0.03 0.06 40000 2500 40000 1300 0.025 0.06 40000 2500 40000 1300 0.025 0.06 R0.4 40000 4800 40000 2400 0.05 0.08 40000 4000 40000 1900 0.04 0.08 40000 4000 40000 1900 0.04 0.08 R0.5 40000 5600 40000 3200 0.06 0.1 40000 5600 40000 3000 0.05 0.1 40000 5600 40000 3000 0.05 0.1 R0.75 40000 6500 40000 4000 0.09 0.15 40000 6500 32000 3200 0.08 0.15 40000 6500 32000 3200 0.08 0.15 R1 40000 6500 39000 4700 0.11 0.2 40000 6500 31000 3500 0.11 0.2 40000 6500 31000 3500 0.11 0.2 R1.25 40000 7000 33000 4500 0.12 0.25 36000 6500 26000 3500 0.12 0.25 36000 6500 26000 3500 0.12 0.25 R1.5 40000 7500 27000 4300 0.13 0.3 32000 6000 22000 3400 0.13 0.3 32000 6000 22000 3400 0.13 0.3 R2 32000 7500 20000 3600 0.15 0.4 25000 6000 16000 2700 0.15 0.4 25000 6000 16000 2700 0.15 0.6 R2.5 25000 6000 16000 2900 0.2 0.5 20000 5400 13000 2300 0.2 0.5 20000 5400 13000 2300 0.2 0.75 R3 21000 5800 13000 2600 0.25 0.6 17000 4700 10000 2000 0.25 0.6 17000 4700 10000 2000 0.25 0.9 R4 16000 4500 10000 2000 0.3 0.8 13000 3600 8000 1500 0.3 0.8 13000 3600 8000 1500 0.3 1.6 R5 13000 3600 8000 1700 0.5 1.0 10000 2900 6400 1200 0.5 1.0 10000 2900 6400 1200 0.5 2.0 R6 9000 2500 6000 1300 0.5 1.2 7200 2000 4800 1000 0.5 1.2 8500 2300 5300 1100 0.5 2.4 I RE a is the inclination angle of the machined surface. If the depth of cut is shallow, the revolution and feed rate can be increased. If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. Standard cutting conditions of austenitic stainless steel, and titanium alloy, please reduce to 60% revolution and 45% feed rate. (Hardened steel (45 55HRC) table above) Mitsubishi Materials 901 Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide