Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ ygjHV Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Side milling Work material Cartoon steel, Alloy steel, Mild steel AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic Stainless steels, Titanium alloys AISI 304, AISI 306, Ti-6AI-4V Oil. DCjmm) Cutting speed (mimh) Revolution (miir1) Feed nte (rnikiin Detith of cut ap(mn DqMh of cut a) mn) Cling ipeed (mMn) Revolution (miir1 Feed nte Deptti of cut ep(nm) Depth of cut eefoim) Cling speed (minin Revolim (miir1) Feed nte (mmlmin) Depth of cut tpM Depth of cut )i(mm) 2 130 21000 700 5 0.2 100 16000 510 5 0.2 80 13000 390 5 0.1 3 130 14000 960 7.5 0.3 100 11000 680 7.5 0.3 80 8500 490 7.5 0.15 4 130 10000 1000 10 0.4 100 8000 690 10 0.4 80 6400 540 10 0.2 5 130 8300 1100 12.5 0.5 100 6400 730 12.5 0.5 80 5100 570 12.5 0.25 6 130 6900 1200 15 0.6 100 5300 810 15 0.6 80 4200 630 15 0.3 8 130 5200 1200 20 0.8 100 4000 840 20 0.8 80 3200 640 20 0.4 10 130 4100 1100 25 1 100 3200 810 25 1 80 2500 590 25 0.5 12 130 3400 1100 30 1.2 100 2700 780 30 1.2 80 2100 550 30 0.6 16 130 2600 920 40 1.6 100 2000 640 40 1.6 80 1600 450 40 0.8 20 130 2100 820 50 2 100 1600 570 50 2 80 1300 420 50 1 Work material Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631, 15-5PH, 17-4PH Copper, Copper alloys Heat resistant alloys lnconel718 Die. Cutting speed Revolution Feed nte Depth of cut Depth of cut Cling speed Revolution Feed nte Depth of cut Depth of cut Cutting speed Revolution Feed nte Depth of cut Dtplh ol cut Dttynm) (mMih) (miir1) (imiMn) ap(nu m ihi (mMn) (mr1 (mm/mir) ip(mm) eetynm) (mfmin) Imiir1) (mmlmin) m) ujimi) 2 75 12000 360 5 0.1 160 25000 830 5 0.2 40 6400 90 5 0.04 3 75 8000 460 7.5 0.15 160 17000 1200 7.5 0.3 40 4200 130 7.5 0.06 4 75 6000 510 10 0.2 160 13000 1300 10 0.4 40 3200 190 10 0.08 5 75 4800 540 12.5 0.25 160 10000 1300 12.5 0.5 40 2500 180 12.5 0.1 6 75 4000 600 15 0.3 160 8500 1500 15 0.6 40 2100 180 15 0.12 8 75 3000 600 20 0.4 160 6400 1500 20 0.8 40 1600 170 20 0.16 10 75 2400 570 25 0.5 160 5100 1300 25 1 40 1300 170 25 0.2 12 75 2000 520 30 0.6 160 4200 1300 30 1.2 40 1100 140 30 0.24 16 75 1500 420 40 0.8 160 3200 1100 40 1.6 40 800 110 40 0.32 20 75 1200 390 50 1 160 2500 970 50 2 40 640 80 50 0.4 ae SMART MIRACLE Coating is not energized because of its nature. Therefore, an external contact (voltaic type) tool setter cannot be used. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. If the depth of cut is shallow, the revolution and feed rate can be increased. Mitsubishi Materials 831 Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide