Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ VnMHZVOH Work material Hardened stainless steels, Cobalt chromium alloy AISI 630, AISI 631 15-5PH.17-4PH Copper, Copper alloys Qaneter DC mm) Cutting Speed (niin) RewMofl fir1 Feed rate (mmlmin) DepthrfHde fW Step (mm) Cutting Speed tnki) Revdutim (rritr1) Feed nte (mmlmh) Depth if Hole ip(mm Step (tint) 6 40 2100 60 6 0.6 120 6400 1200 g 3 8 40 1600 50 8 0.6 120 4800 860 12 4 10 40 1300 40 10 0.6 120 3800 680 15 5 12 40 1100 30 12 0.6 120 3200 580 18 5 16 40 800 20 16 0.6 120 2400 430 24 5 . . - - . i C I-1- General-purpose conditions Work material Carbon steel, Alloy steel, Mild steel AIS11045, AISI 4140,ASTM A36, AISI1010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20.AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steels, Titanium alloys stainless steels, Titanium alloys AISI 304, AISI 316, Ti-6AI-4V etc. Harter Cutting Spud Revolution Feed nte Depth of Hole Sty Ciing Speed Revolution Feed nte Depth of Hole Step Cutting Spead Revdufion Fuad rate DythdHdi Sty IKtynm) (mtnii (miir1) (imtnin) ip(mn) (im (mkrin) Jnin-1 (mm/mir) ap(mm) Iniminl miir1) (mmlmin) "i) m 6 100 5300 950 9 0.6 70 3700 440 9 0.6 60 3200 100 6 0.3 8 100 4000 720 12 0.7 70 2800 340 12 0.7 60 2400 70 8 0.3 10 100 3200 580 15 0.75 70 2200 260 15 0.75 60 1900 60 10 0.3 12 100 2700 490 18 0.75 70 1900 230 18 0.75 60 1600 50 12 0.3 16 100 2000 360 24 0.75 70 1400 170 24 0.75 60 1200 40 16 0.3 Work material Hardened stainless steels, Cobalt chromium alloy AISI 630, AISI 631 15-5PH.17-4PH Copper, Copper alloys DMer DCjmm) Cutting Speed (mtnii Revolution (nir'l Feed rate (mmlmin) Depth uf Hole ipfmm) Sty (nm) Cutting Speed (mtnin) Revolution tnir1) Feed rate (mmlmin) Depth of Hole ipH Step 6 40 2100 60 6 0.3 120 6400 1200 9 0.6 8 40 1600 50 8 0.3 120 4800 860 12 0.7 10 40 1300 40 10 0.3 120 3800 680 15 0.75 12 40 1100 30 12 0.3 120 3200 580 18 0.75 16 40 800 20 16 0.3 120 2400 430 24 0.75 1 1 1 - 1 r SMART MIRACLE Coating is not energized because of its nature. Therefore, an external contact (voltaic type) tool setter cannot be used. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abonrmal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. Mitsubishi Materials 785 Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide