Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ VnMHZV General-purpose conditions Work material Carbon steel, Alloy steel, Mild steel AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steels, Titanium alloys Titanium alloys AISI 304, AISI 316, Ti-6AI-4V DCH Mhg Speed (mimin Revoiolon (liit1 Feed rate (mmlmin) Di i of cut vM Cutting Speed (mimin) Revolution (miir1 Feed rati (mmlmin) Depth of cut ap(mm Cutting Speed (ninin) Revolution fyniir1) Feed nte (mmlmii) Dejitli of cut ip(mm) 1 100 32000 250 0.5 80 25000 99 0.5 60 19000 80 0.5 1.5 100 21000 290 0.75 80 17000 130 0.75 60 13000 100 0.75 2 100 16000 410 2 80 13000 210 2 60 9500 190 2 3 100 11000 500 3 80 8500 240 3 60 6400 190 3 4 100 8000 630 4 80 6400 300 4 60 4800 210 4 5 100 6400 630 5 80 5100 300 5 60 3800 210 5 6 100 5300 630 6 80 4200 330 6 60 3200 220 6 8 100 4000 550 8 80 3200 320 8 60 2400 240 8 10 100 3200 510 10 80 2500 270 10 60 1900 260 10 12 100 2700 430 12 80 2100 250 12 60 1600 250 12 16 100 2000 360 12 80 1600 220 12 60 1200 190 12 20 100 1600 290 12 80 1300 180 12 60 950 150 12 Work material Hardened stainless steels, Cobalt chromium alloy AISI 630, AISI 631 15-5PH.17-4PH Copper, Copper alloys Heat resistant alloys lnconel718 DCH Cutthg Speed (mimin) Rnvolutioi (miir1) Fend rata (mmlmin) Depth of cut Cutting Spied (mimin) Revdution (miir1) Feed nte mmlmin) Depth of cot op(mm Cutting Speed (minin) Revolution (niir1 Feed rate (mmlmh Cepith of cut ip mm 1 45 14000 60 0.3 120 38000 300 0.5 25 8000 30 0.2 1.5 50 11000 87 0.4 120 25000 350 0.75 25 5300 40 0.3 2 50 8000 130 1 120 19000 490 2 25 4000 55 0.6 3 50 5300 150 1.5 120 13000 590 3 25 2700 64 0.9 4 50 4000 190 2 120 9500 750 4 25 2000 70 1.2 5 50 3200 190 2.5 120 7600 750 5 25 1600 71 1.5 6 50 2700 210 3 120 6400 760 6 25 1300 72 1.8 8 50 2000 200 4 120 4800 670 8 25 990 78 2.4 10 50 1600 170 5 120 3800 600 10 25 800 89 3 12 50 1300 150 6 120 3200 510 12 25 660 84 3.6 16 50 990 140 8 120 2400 430 12 25 500 63 4.8 20 50 800 110 10 120 1900 340 12 25 400 50 6 DC SMART MIRACLE Coating is not energized because of its nature. Therefore, an external contact (voltaic type) tool setter cannot be used. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abonrmal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. When the Depth of cut is small, the feed rate can be increased. Mitsubishi Materials 779 Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide