Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ ELS Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS (): Indicates standard feed rate for slotting. Work material Structural steel. Carbon steel AIS11045, AIS11050 Carbon steel, Alloy steel (20 30HRC) AIS11055, AISI P20 Alloy steel, Tool steel, Pre-hardened steel (30 35HRC) AISI H13 Austenitic stainless steel AISI 304, AISI 316 Cast iron AISI No 35 B Aluminium alloy Oil. Mufion Ftal nte Reiokition Feed nte Revolution Feed nte Revolution Feed nte Revdutin Feed nte Revdution Feed nte DC(mm) (mir1 (mmlmn) miir1) (mm/min) (miir1 (mmlminl (mirr1 (nriMn) (mirr1 (mm/min) (mir' (mmlmri 1 4000 35(30) 3200 22(16) 2250 16(15) 1800 12(10) 3400 40(30) 8250 80(60) 2 2300 40(30) 2000 30(20) 1350 20(16) 1000 14(11) 2000 40(35) 5100 90(70) 3 1700 40(35) 1350 30(25) 1000 25(20) 850 16(14) 1500 45(35) 3600 110(90) 4 1350 45(40) 1000 35(30) 800 25(20) 650 16(14) 1200 50(40) 2850 150(120) 5 1200 55(40) 900 40(35) 700 30(22) 550 20(14) 1000 55(45) 2400 170(130) 6 1000 55(45) 750 40(35) 600 30(25) 450 22(16) 850 60(50) 2100 180(145) 8 850 60(50) 600 45(35) 450 30(25) 350 22(16) 650 65(50) 1650 210(165) 10 650 66(55) 480 45(40) 350 30(25) 285 25(20) 550 70(60) 1350 200(160) 12 550 60(50) 400 45(35) 300 30(22) 240 22(16) 450 65(50) 1200 200(155) 16 400 55(40) 300 40(35) 250 25(20) 180 20(15) 330 55(45) 900 160(130) 20 330 45(35) 240 35(30) 180 20(16) 150 16(14) 270 50(40) 720 140(110) 25 260 40(30) 200 30(22) 140 20(15) 110 15(11) 200 40(35) 570 120(100) 30 220 35(30) 150 25(20) 120 15(12) 90 12(10) 180 40(30) 480 110(90) 40 160 30(22) 110 20(15) 90 12(10) 70 10(9) 135 30(25) 360 90(70) 50 120 22(16) 90 15(12) 70 11(9) 55 9(7) 105 25(20) 290 70(60) 60 100 20(15) 70 15(11) 60 10(9) 40 7(6) 90 22(16) 240 60(50) <0.1DC (DC< 3) <0.1DC (DC < 2) 0.3DC (42 DC i>3) <0.5DC (DC> 03) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. 1160 Mitsubishi Materials