Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ DC2XLB Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Work material Cemented carbide Alumina Zirconia Dil. R m Nedi length RevduSon Feed rate Depth if at Depth of ail Revdution Feed nte Deptti of cut Depth of cut DC(mm TTX RE (mm LU mm (ill4 (mmlmin) ip im n(mm) fniiH nun/mini iptnm) ie(mm 0.2 0.1 0.5 30000 30 0.005 0.01 30000 30 0.005 0.01 0.4 0.2 1 30000 100 0.015 0.08 30000 100 0.015 0.08 0.6 0.3 1.5 30000 200 0.03 0.14 30000 200 0.03 0.14 0.8 0.4 2 30000 250 0.04 0.19 30000 250 0.04 0.19 1 0.5 2.5 30000 300 0.05 0.25 30000 300 0.05 0.25 1 0.5 5 30000 300 0.05 0.25 30000 300 0.05 0.25 1.5 0.75 3.8 30000 300 0.075 0.275 30000 300 0.075 0.275 2 1 6 30000 300 0.1 0.3 30000 300 0.1 0.3 2 1 10 30000 300 0.1 0.3 30000 300 0.1 0.3 3 1.5 8 27500 275 0.125 0.33 27500 275 0.125 0.33 4 2 10 24000 240 0.15 0.35 24000 240 0.15 0.35 5 2.5 10 22000 220 0.175 0.37 22000 220 0.175 0.37 6 3 10 20000 200 0.2 0.4 20000 200 0.2 0.4 ae Work material Silicon carbide Silicon nitride Quartz glass Dil. R US Neck length Revdution Feed nte Depth of cut Depth of cut Revolution Feed nte Depth of cut Depth ol cut DCfoim RE (mm LU mm (mir'l (mmfmin) ap)n ae(mm (min l (mmlmin) ie m 0.2 0.1 0.5 30000 15 0.003 0.005 30000 45 0.008 0.015 0.4 0.2 1 30000 50 0.008 0.04 30000 150 0.023 0.12 0.6 0.3 1.5 30000 100 0.015 0.07 30000 300 0.045 0.21 0.8 0.4 2 30000 125 0.02 0.095 30000 375 0.06 0.285 1 0.5 2.5 30000 150 0.025 0.125 30000 450 0.075 0.375 1 0.5 5 30000 150 0.025 0.125 30000 450 0.075 0.375 1.5 0.75 3.8 30000 150 0.038 0.138 30000 450 0.113 0.413 2 1 6 30000 150 0.05 0.15 30000 450 0.15 0.45 2 1 10 30000 150 0.05 0.15 30000 450 0.15 0.45 3 1.5 8 27500 138 0.063 0.165 27500 413 0.188 0.495 4 2 10 24000 120 0.075 0.175 24000 360 0.225 0.525 5 2.5 10 22000 110 0.088 0.185 22000 330 0.263 0.555 6 3 10 20000 100 0.1 0.2 20000 300 0.3 0.6 ae The cemented carbide in the above mentioned cutting conditions table is based on CIS standard VM-40(90HRA). Air blow or dry processing is recommended with cemented carbide processing. Note: Using coolants or oil mists may decrease tool longevity. The use of a water soluble cutting oil is recommended with the processing of hard brittle materials other than the cemented carbide mentioned in the above table. Be sure to refuel the oil and eliminate any chip discharge that adheres to the tool. Cutting conditions may need adjustments depending on the type of work material. If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. Implementation of special countermeasures is recommended since fine chip discharge may enter gaps in the processing machinery. 1126 Mitsubishi Materials