1898 Каталог WALTER 2012 Металлорежущий инструмент и оснастка Valenite для станков Стр.E296

Каталог WALTER 2012 Инструмент и оснастка Valenite Стр. E296 1898 ENG Lab2u

WALTER Technical information Milling Prototyp Cutting data for shoulder / slot milling Cutting tool material HSS Family Des. Page HR Kordel P3120387 30° E 203 F 30 HNR Kordel P3120537 30° E 202 F 30 eT Qr Vc in ft/min Feed matrices VT begin on page E 310 Material group Classification of the main material groups and code letters Brinell hardness HB Tensile strength Rm N/mm2 Machining group 1 6 32mm Z 3 6 uncoated + ACN Workpiece material 1/1 1/10 VT p Unalloyed steel C > 0.25 % annealed 125 428 P1 130 130 195 A C > 0.25 < 0.55 % annealed 190 639 P2 130 165 195 A C > 0.25 < 0.55 % tempered 210 708 P3 65 65 100 A C > 0.55 % annealed 190 639 P4 65 65 100 A C > 0.55 % tempered 300 1,013 P5 35 65 65 A Free cutting steel (short-chipping) annealed 220 745 P6 65 65 100 A Low-alloyed steel annealed 175 591 P7 65 65 100 A tempered 300 1,013 P8 35 65 65 A tempered 380 1,282 P9 35 65 65 A tempered 430 1,477 P10 35 35 65 A High-alloyed steel and high-alloyed tool steel annealed 200 675 P11 65 65 100 A hardened and tempered 300 1,013 P12 35 65 65 A hardened and tempered 400 1,361 P13 35 35 65 A Stainless steel ferritic / martensitic, annealed 200 675 P14 35 35 35 A martensitic, tempered 330 1,114 P15 35 35 35 A M Stainless steel austenitic, quench hardened 200 675 M1 35 65 65 B austenitic, precipitation hardened (PH) 300 1,013 M2 35 35 35 B austenitic/ferritic, duplex 230 778 M3 35 35 35 B K Malleable cast iron ferritic 200 675 K1 65 65 100 A pearlitic 260 867 K2 35 65 65 A Grey cast iron low tensile strength 180 602 K3 65 65 100 A high tensile strength / austenitic 245 825 K4 65 65 100 A Cast iron with spheroidal graphite ferritic 155 518 K5 65 65 100 A pearlitic 265 885 K6 35 65 65 A Cast iron with vermicular graphite 200 675 K7 35 65 65 A N Aluminum wrought alloys cannot be hardened 30 N1 260 330 425 C hardenable, hardened 100 343 N2 260 330 425 C Cast aluminum alloys < 12 % Si, not hardenable 75 260 N3 165 195 260 C < 12 % Si, hardenable, hardened 90 314 N4 165 195 260 C > 12 % Si, not hardenable 130 447 N5 100 100 165 C Magnesium alloys 70 250 N6 165 195 260 C Copper and copper alloys (bronze / brass) unalloyed, electrolytic copper 100 343 N7 165 195 295 C Brass, bronze, red brass 90 4 31 N8 165 230 295 C Cu-alloys, short-chipping 110 382 N9 165 230 295 C high-strength, Ampco 300 1,013 N10 35 35 65 C S Heat-resistant alloys Fe-based annealed 200 675 S1 hardened 280 943 S2 Ni or Co base annealed 250 839 S3 hardened 350 1,177 S4 cast 320 1,076 S5 Titanium alloys Pure titanium 200 675 S6 a and p alloys, hardened 375 1,262 S7 P alloys 410 1,396 S8 Tungsten alloys 300 1,013 S9 Molybdenum alloys 300 1,013 S10 H Hardened steel hardened and tempered 50 HRC H1 hardened and tempered 55 HRC H2 hardened and tempered 60 HRC H3 Hardened cast iron hardened and tempered 55 HRC H4 O Thermoplasts without abrasive fillers O1 Thermosetting plastics without abrasive fillers O2 Plastic, glass-fiber reinforced GFRP O3 Plastic, carbon-fiber reinforced CFRP O4 Plastic, aramid fiber reinforced AFRP O5 Graphite (technical) 80 Shore O6 1 The machining groups are assigned from page H 8. E 296