Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ VFESDBL Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS VF2SDB/L Overhang Below 5DC (DC Dia.) Work material Alloy steel, Tool steel, Pre-hardened steel AISI H13, AISI W1-10, AISI P21 Hardened steel (45 55HRC) AISI H13 Hardened steel (55 62HRC) AISID2 R RE 0 15' >15 Depth of cut ip (mm) Depth if cut ae (mm) 1 1 ’ PIS' Depth if cut ip M Depth of cut le (mm o 15‘ 0>ti Depth of cut >P (mm Depth if cut ae Revdution (miir1) Feed nte (mmlmii Revokidon miir'l Feed nte (mm/min) Revolution (mir1) Feed nte (mni/mjn) Revdution miir') Feed nte (mm/min) Revdution tynlir1) Feed nte (mm/min) Revolution (miir1) Feed nte (mmtnin R0.5 40000 5200 36000 2300 0.10 0.25 40000 5200 36000 2300 0.10 0.25 40000 5000 40000 2400 0.05 0.10 R1 40000 6000 36000 3500 0.20 0.50 40000 6000 36000 3500 0.20 0.50 36000 5000 24000 2400 0.10 0.20 R1.5x3 29000 4600 19000 2400 0.20 0.50 25000 4000 16000 2000 0.20 0.50 17000 2400 11000 1000 0.12 0.30 R1.5 37000 7000 24000 3000 0.30 0.75 37000 7000 24000 3000 0.30 0.75 25000 6000 16000 2200 0.12 0.30 R2x4 24000 4300 15000 2200 0.25 0.70 19000 3400 13000 1700 0.25 0.70 12000 1900 8200 900 0.13 0.40 R2 30000 6500 19000 2800 0.40 1.00 28000 6000 19000 2600 0.40 1.00 18000 4800 12000 2000 0.13 0.40 R2.5 25000 6000 16000 2600 0.50 1.30 22000 5000 16000 2300 0.50 1.25 15000 4200 9500 1700 0.15 0.50 R3 22000 6000 14000 2400 0.60 1.80 18000 4500 12000 1900 0.60 1.50 12000 3500 8000 1600 0.20 0.60 R4 19000 5200 12000 2200 0.80 2.40 15000 3800 9500 1700 0.80 2.00 9800 3000 6500 1300 0.20 0.80 R5 15000 4300 9500 2000 1.00 3.00 11000 3000 7000 1500 1.00 2.50 7500 2400 5000 1000 0.20 1.00 R6 12000 3400 8000 1800 1.20 3.60 9000 2400 6000 1400 1.20 3.00 6000 1900 4000 800 0.30 1.20 R8 9000 2600 6000 1500 1.60 4.80 7000 1900 4500 1100 1.60 4.00 4500 1500 3000 600 0.30 1.60 R10 7500 2200 4800 1200 2.00 6.00 5500 1500 3600 900 2.00 5.00 3600 1200 2500 500 0.30 2.00 a is the inclination angle of the machined surface. If the depth of cut is shallow, the revolution and feed rate can be increased. If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. Overhang 7DC (DC Dia.) Work material Alloy steel, Tool steel, Pre-hardened steel AISI H13, AISI W1-10, AISI P21 Hardened steel (45 55HRC) AISI H13 R RE (nr) Revolution (miir1) Feed nte (mmlmin) Depth ol nit ap(mm Depth of cut ie( Revolution (miir1 Feed nte (mm/min) Depth of nit jp(mm Depth of cut ee(mn R1.5x3 R2x4 R3 R4 R5 R6 R8 R10 16000 13000 10000 8000 6000 5000 3800 3000 2000 2000 2000 1800 1600 1300 1000 800 0.10 0.15 0.20 0.30 0.40 0.45 0.60 0.80 0.30 0.50 1.00 1.50 2.00 2.40 3.00 4.00 13000 10000 8000 6400 4800 4000 3100 2500 1500 1500 1600 1400 1200 1000 800 650 0.10 0.15 0.20 0.40 0.40 0.45 0.60 0.80 0.30 0.50 0.80 1.20 1.60 2.00 2.50 3.00 If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. 938 Mitsubishi Materials