Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ voxl Recommended cutting condition Shoulder milling Work material Carbon steel, Alloy steel, Austenitic stainless steel, Titanium alloy, Cobaly chromium alloy, Copper, Copper alloy AIS11045, AISI 4140, AISI 4340, AISI 304, AISI 316, AISI 304LN, AISI 316LN, Ti-6AI-4V Heat resistant alloys, Pre-hardened steel, Hardened steel lnconel718, AISI P21, AISI P20, AISI H13, AISI L6, AISI 431, AISI 420 DMti Neck length Cutting Speed Revolutkin Feed nte Depth if cut Depth of cut Cutting Speed RevgMte Feed nte Depth of cut Depth tf cut DCH LU(mm jmirrin) (miir1 (mmlmin) i M aeH (m/min (miir1) ImmMn) m aejnm) 0.2 0.6 25 40000 360 0.03 0.01 20 32000 290 0.03 0.01 0.3 0.9 40 40000 480 0.045 0.015 20 21000 250 0.045 0.015 0.3 1.5 40 40000 360 0.045 0.015 20 21000 190 0.045 0.015 0.4 1 50 40000 800 0.06 0.02 20 16000 320 0.06 0.02 0.4 1.8 50 40000 560 0.06 0.02 20 16000 220 0.06 0.025 0.5 1.5 60 38000 910 0.075 0.025 20 13000 310 0.075 0.025 0.5 2.5 60 38000 610 0.075 0.025 20 13000 210 0.075 0.025 0.5 3 60 38000 550 0.075 0.025 20 13000 180 0.075 0.025 0.6 3 60 32000 640 0.09 0.03 20 10500 210 0.09 0.03 0.7 3.5 60 27000 650 0.11 0.035 20 9100 200 0.11 0.035 0.8 2.4 60 24000 960 0.12 0.04 20 8000 260 0.12 0.04 0.8 3 60 24000 860 0.12 0.04 20 8000 230 0.12 0.04 0.8 4 60 24000 670 0.12 0.04 20 8000 190 0.12 0.04 1 5 60 20000 800 0.15 0.05 20 6500 210 0.15 0.05 Bottom face milling Work material Carbon steel, Alloy steel, Austenitic stainless steel, Titanium alloy, Cobaly chromium alloy, Copper, Copper alloy AIS11045, AISI 4140, AISI 4340, AISI 304, AISI 316, AISI 304LN, AISI 316LN, Ti-6AI-4V Heat resistant alloys, Pre-hardened steel, Hardened steel lnconel718, AISI P21, AISI P20, AISI H13, AISI L6, AISI 431, AISI 420 DMei Neck length Cutting Speed Revdution Feed nte Depth if cut Depth of cut Cutting Speed Revglutim Feed nte Depth of cut Depth of cut DCjtrni) LU(mm ImMnn) (miir1) (mmlmin) ipH mlmiii miir1) IrnnMn) m aejmrn) 0.2 0.6 25 40000 360 0.015 0.2 20 32000 290 0.015 0.1 0.3 0.9 40 40000 480 0.025 0.3 20 21000 250 0.025 ±=0.15 0.3 1.5 40 40000 360 0.02 0.3 20 21000 190 0.02 0.15 0.4 1 50 40000 800 0.03 0.4 20 16000 320 0.03 0.2 0.4 1.8 50 40000 560 0.02 0.4 20 16000 220 0.02 0.2 0.5 1.5 60 38000 910 0.04 0.5 20 13000 310 0.04 0.25 0.5 2.5 60 38000 610 0.03 0.5 20 13000 210 0.03 0.25 0.5 3 60 38000 550 0.03 0.5 20 13000 180 0.03 0.25 0.6 3 60 32000 640 0.035 0.6 20 10500 210 0.035 0.3 0.7 3.5 60 27000 640 0.035 0.7 20 9100 190 0.035 0.35 0.8 2.4 60 24000 960 0.06 0.8 20 8000 260 0.06 0.4 0.8 3 60 24000 840 0.05 0.8 20 8000 230 0.05 0.4 0.8 4 60 24000 670 0.04 0.8 20 8000 190 0.04 0.4 1 5 60 20000 800 0.05 1 20 6500 210 0.05 0.5 SMART MIRACLE Coating is not energized because of its nature. Therefore, an external contact (voltaic type) tool setter cannot be used. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective If the depth of cut is shallow, the revolution and feed rate can be increased. Mitsubishi Materials 833 Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide