Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ VOMHVRB Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Side milling The rigidity of the machine or workpiece and chip discharge are sufficient at high efficiency conditions. The rigidity of the machine or workpiece or chip discharge is insufficient at general-purpose conditions. High efficiency conditions Work material Carbon steel, Alloy steel, Mild steel AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic Stainless steels. Titanium alloys AISI 304, AISI 306, Ti-6AI-4V Dii Cutting ipeed Mtion Feediale Depth of cut Depth of cut Cling speed Revolution FhiI rate Depth tf cut Depth of cut Cutting ipeed Revolution Feed nte Depth of cut Depth ol cut DC nm) mM miir'l (nriMn ip(mm n nri (nMn (min-1 (mm/mir ip(nm ae(nm Iniminl (mir'l (mmlmin i eejnm) 2 150 24000 2400 3 0.6 120 19000 1100 3 0.6 100 16000 830 3 0.6 3 150 16000 2600 4.5 0.9 120 13000 1200 4.5 0.9 100 11000 880 4.5 0.9 4 150 12000 2600 6 1.2 120 9500 1300 6 1.2 100 8000 900 6 1.2 5 150 9500 2600 7.5 1.5 120 7600 1300 7.5 1.5 100 6400 900 7.5 1.5 6 150 8000 2600 9 1.8 120 6400 1300 9 1.8 100 5300 1100 9 1.8 8 150 6000 2500 12 2.4 120 4800 1300 12 2.4 100 4000 1200 12 2.4 10 150 4800 2300 15 3 120 3800 1200 15 3 100 3200 1300 15 3 12 150 4000 1900 18 3.6 120 3200 1200 18 3.6 100 2700 1200 18 3.6 16 150 3000 1600 24 4.8 120 2400 960 24 4.8 100 2000 960 24 4.8 20 150 2400 1300 30 6 120 1900 760 30 6 100 1600 770 30 6 25 150 1900 1100 37.5 7.5 120 1500 600 37.5 7.5 100 1300 620 37.5 7.5 Work material Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631,15-5PH,17-4PH Copper, Copper alloys Dii DCH Cutting ipeid (mlmin Revolution (miir1) Fnd nil mniMn Diplh of cut apjnn) Ikpthofcut ie nm Cling spied (mimin Revolution (min-1 Fnd nti (mMI Dopfh of cut iptnm Dipth of cut ae nm Cutting spud lin/min Rndutian miir1) Fnd nil (mmlmin Dipth of cut i Dqth ol cut ee mn) 2 75 12000 720 3 0.4 180 29000 2900 3 0.6 40 6400 230 3 0.2 3 75 8000 770 4.5 0.6 180 19000 3000 4.5 0.9 40 4200 240 4.5 0.3 4 75 6000 790 6 0.8 180 14000 3000 6 1.2 40 3200 240 6 0.4 5 75 4800 810 7.5 1 180 11000 3000 7.5 1.5 40 2500 240 7.5 0.5 6 75 4000 810 9 1.2 180 9500 3000 9 1.8 40 2100 250 9 0.6 8 75 3000 840 12 1.6 180 7200 3000 12 2.4 40 1600 260 12 0.8 10 75 2400 770 15 2 180 5700 2700 15 3 40 1300 290 15 1 12 75 2000 720 18 2.4 180 4800 2300 18 3.6 40 1100 280 18 1.2 16 75 1500 600 24 3.2 180 3600 1900 24 4.8 40 800 200 24 1.6 20 75 1200 480 30 4 180 2900 1600 30 6 40 640 160 30 2 25 75 950 380 37.5 5 180 2300 1300 37 7.5 40 510 130 37.5 2.5 Heat resistant alloys lnconel718 Mitsubishi Materials 1045 Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide