765 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.765

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 765 0765 ENG Lab2u

Hoffmann Group 47 Axn Quick-change lathe tool post and toolholders Quick-change lathe tool post with eccentric clamping Application: Supplied with: Note; Place the lathe tool post with its surface-ground face on to the cross slide in a horizontal position and clamp it. To do this, the bore of the centring plate must have been turned beforehand. Alignment is performed with the boring bar and boring bar holder clamped in position, aligned at right angles to the face plate. Then adjust the pointer to the zero mark of the cover disc and tighten the T-bolt securely. For precision lathe work or heavy roughing cuts, it is advisable to secure the post with two dowel pins. The holes are pre-drilled. 1 eccentric lever for No. 318000,1 tool post key for No. 318100 / 8200. For types and further applications see the table. Quick-change turning toolholder Type AA I A I B I c I Uliliffl Quick-change lathe tool post 229.68 282.15 416.79 646.47 maximum drive power of lathe kW 1.104 1.472 5.888 11.04 maximum cross slide width SB mm 80 100 150 180 maximum turning tool height h mm 12 20 32 45 Bore 0 of the head mm 13 20 32 40 Bore 0 of the centering plate mm 10 10 13 16 Width mm 70 100 150 200 Height mm 37 54 75 105 maximum reach A mm 30 48 71 100 With flat tool base. Equipped with locking height adjustment screw and 3 tool clamping screws. Note: When ordering square parts No. 318110 - 318130 please specify their number and the size of the quick-change turning toolholder. Type AA12/50 1 A16/75 1 A16/90 I A20/75 1 A20/90 I B25/120 1 B25/140 Quick-change turning toolholder 77.02 76.82 76.82 78.01 78.01 120.29 120.29 suitable for 318000 AA A A A A B B Height of the toolholder mm 12 16 16 20 20 25 25 Length mm 50 75 90 75 90 120 140 Thickness of tool support W mm 6 8.75 8.75 10 10 12 12 Type C32/150 I C32/170 1 C40/150 I C40/170 Quick-change turning toolholder 122.76 122.76 189.09 189.09 204.93 204.93 suitable for 318000 B B C C C C Height of the toolholder mm 32 32 32 32 40 40 Length mm 120 140 150 170 150 170 Thickness of tool support W mm 14 14 17 17 17 18 Quick-change boring bar holder with prism Application: For holding boring bars and other tools with a cylindrical shank. Equipped with locking height adjustment screw and 3 tool clamping screws. Profile-ground toothing. Repetition accuracy 0.01 mm Height-adjustment screwNo.318110. Height-adjustment nut No. 318120. 318000 Clamp screw No. 318130. Type AA I I B I C40 C50 Quick-change boring bar holder 81.58 80.39 133.16 228.69 244.53 suitable for 318000 AA A B C C for boring bar 0 mm 12 20 30 40 50 Length mm 50 85 130 160 160 Vee block base Application: For boring bar holder No. 318200 size B. For holding small boring bars and boring heads. Vee block base 18.77 suitable for 318200 B Length mm 130 i Morse taper sleeve with ejection slot Application: The MT sleeve is clamped in the Vee block of the boring bar holder No. 318200 size B. This allows tools with Morse taper shank up to MT 2 to be mounted in the boring bar holder. Note: Vee bases / Morse taper sleeves for sizes C and D are available ex works. Rear of sleeve fitted with release screw 8AF. Morse taper sleeve 45.64 suitable for 318200 B ShankMT 2 External 0 mm 30 318220 765 318200