53 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.53

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 53 0053 ENG Lab2u

Hoffmann Group 47 HSS E DIN 1869 h8 01 4asat M Extra long jobber drills plain shank HSS-E 116285 - TiAIN and anti-friction coating, low wear and low tendency to edge build-up. Advantage: 116280 - Particularly suitable for drilling under difficult conditions, e.g. insufficient cooling of the cutting edges due to poor chip evacuation. 116285 - Flute length to DIN 340. For high-tensile tempered steels, including TOOLOX. Parabolic flutes with strong core. Large flute. 116280 typeFS Type FS 135" Type N 118" 116285 Suitable for/ A u v( m/min Alu cast >10% Si X < 500 N X < 750 N x x < 900 N < 1100 N X < 1400 N X <55 HRC X <60 HRC X <65 HRC X <67 HRC X <70 HRC TOOLOr 33 HRC TOOLOr 44 HRC IN0X < 900N INOX CuZn >900N 6 i 4k ISO code N N P H r n 116280 38 38 28 22 116285 I 38 28 22 7 5 10 8 10 5 70 0h8x Overall length iEHinu f tl 116280 116285 1 L X < 750 N Jobber drill, extra long HSS-E FS II N f mm TiAIN mm mm/rev 3x150 19.16 15.74 100 66 150 0.05 3x190 28.91 - 130 - 190 0.05 3,5x165 23.86 - 115 - 165 0.05 3,5X210 56.63 - 145 - 210 0.05 4x175 22.87 18.71 120 78 175 0.05 4x220 57.62 - 150 - 220 0.05 4X280 73.85 60.19 190 78 280 0.05 4,5x185 50.49 - 125 - 185 0.05 4,5X235 59.40 - 160 - 235 0.05 5x195 25.94 21.09 135 87 195 0.07 5x245 61.78 - 170 - 245 0.07 5x315 83.56 68.90 210 87 315 0.07 5,5x205 30.99 - 140 - 205 0.07 5,5x260 66.73 - 180 - 260 0.07 6x205 29.90 24.26 140 91 205 0.07 6x260 49.90 - 180 - 260 0.07 6x330 87.71 71.28 225 91 330 0.07 0h8x Overall length mm 6,3x275 6,8x225 7x225 7X290 7,5x290 8x240 8x305 8x390 8,5X240 8,5x305 9x250 9x320 9,5x320 10x265 10x340 10x430 10,2x340 f L 116280 11 6285 ti L Jobber drill, extra long HSS-E FS II TiAIN mm 74.84 - 190 - 275 47.42 - 155 - 225 49.01 - 155 - 225 78.80 - 200 - 290 83.95 - 200 - 290 53.46 43.56 165 109 240 92.47 - 210 - 305 102.47 83.75 265 109 390 60.79 - 165 - 240 90.49 - 210 - 305 82.96 - 175 - 250 100.98 - 220 - 320 105.93 - 220 - 320 83.95 69.10 185 121 265 109.40 - 235 - 340 141.08 114.84 295 121 430 117.32 - 235 - 340 HSS DIN 1 'A a 1898 A 118° 1:50 boaiaiii Taper pin drills, plain shank Conically increasing cutting edges with chip breaker flutes on the circumference. Special surface treatment. Advantage: Conical holes 1:50 for taper pins to ISO 2339 (DIN 1 and ISO 8736 (DIN 7978) can be drilled in a single operation. Note: For finishing use taper pin reamers No. 161200. Pre-drilling with straight shank taper pin drill No. 116310. Finished hole for taper pin to 1502339 (DIN 1). Ream accurately with taper pin reamer. Suitable for/ Alu Alu v, m/min <3 > a XXX < 500 N < 750 N < 900 N XXX < 1100 N < 1400 N <55 HRC X X <60 HRC <65 HRC X <67 HRC X N0X N0X <70HRC <900N >900N Ti > 850 N Graphite GRP CRP Uni a 6 ISO code P H rn H N 116310 1 24 20 Nominal 0 d, 116310 Straight shank taper pin drill 56.23 59.60 72.67 82.76 smallest largest L, 0d, 0d, I mm L mm f mm/rev 2.9 4.06 5 58 100 4 0.05 3.9 5.26 5 68 112 5 0.05 4.9 6.36 5 73 122 6.3 0.05 5.9 8 5 105 160 8 0.05 Nominal 0 <1, mm " 116310 smallest 0d2 mm largest 0d3 mm L, L2 X Straight shank taper pin drill mm 1 mm 1 i n im <750N f mm/rev 8 110.39 7.9 10.8 5 145 207 10 0.05 10 155.93 9.9 13.4 5 175 245 12.5 0.07 12 221.76 11.8 16 10 210 290 16 0.07 53