49 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.49

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 49 0049 ENG Lab2u

Hoffmann Group 47 HSS DIN 340 h8 s 4 mm Type N S IIB” Garant Long jobber drills, deep hole drills, plain shank 116000- Steam tempered from 2 mm. Particularly for deep hole drilling (for deep holes, repeated chip evacuation is necessary). 116040 - Strengthened core without core taper. Precision ground point. Wide flutes with heavily honed back edges. Bright finish. 116060 - Considerably strengthened core without core taper. Precision ground point. Advantage: 116000 - Especially suitable for long reach purposes. (When used to drill deep holes, low feed rates and frequent drill pecks are necessary). 116040 - For deep hole drilling and for use with drill bushings. 116060 - For drilling deep holes under difficult conditions, e.g. insufficient cooling of the cutting edges due to poor chip evacuation (up to 10x drill 0 chip evacuation is not necessary). Type a 2.5 mm Type W 130° 40° 130° itH 116000 nARA“T 11 6040 116060 38° Drill bushing holder 1-1.5xhole<3 Accurate drilling even on difficult workpiece surfaces. Suitable for/ v( m/min Alu plastics cJg2£2 Alu cast >10% Si X < 500 N X < 750 N X <900N X < 1100 N X < 1400 N X <55 HRC X < SO HRC X <65 HRC X <67 HRC X <70 HRC INOX <900N INOX >900N Ti > 850 N GG(G) Graphite GRP CRP 6 6 -f ISO code N Mri Mn P H K N 40 30 25 25 116040 70 45 40 116060 70 50 50 37 31 31 0h8 “116040 " 116060 O 1 0h8 SKEwE “116040 Jobber drill long HSS Deep-hole drill HSS J Jobber drill long HSS N w FS L N w mm TiAIN mm o 5.64 5 15 35 4,1 2.48 - 0,8 4.37 5 25 46 4,2 2.48 6.29 1 3.56 - 9.95 5 33 56 4,S 2.79 7.33 1,1 3.70 - 9.95 5 37 60 4,8 3.29 - 1 V 3.54 - 9.95 5 41 65 5 3.10 7.13 1,3 3.20 - 10.99 5 41 65 5,2 3.39 - 1 1/4 3.00 - 10.49 5 45 70 5,5 3.58 9.26 1,5 2.57 - 9.31 5 45 70 5,8 3.59 - 1 1,6 2.66 - 8.71 5 50 76 6 3.88 9.36 1,7 2.66 - 8.71 5 50 76 6,2 4.06 - 1 1,8 2.66 - 8.47 5 53 80 6,5 4.16 10.40 1,9 2.66 - 8.32 5 53 80 6,8 6.04 - 1 2 1.79 - 8.07 5 56 85 7 4.85 12.53 2,1 2.12 - 9.31 5 56 85 U 6.59 - I 2,2 2.12 - 9.41 5 59 90 7,S 5.80 15.05 2,3 2.12 - 9.60 5 59 90 7,8 7.03 - I 2,4 2.12 - 9.66 5 62 95 8 5.84 14.11 2,5 1.88 4.46 8.32 5 62 95 8,2 7.03 - 1 2,6 2.29 - 9.66 5 62 95 8,5 6.89 18.27 2,7 2.35 - 9.76 5 66 100 7.23 17.18 2,8 2.35 - 9.76 5 66 100 ,s 8.81 P - I 2,9 2.36 - 10.00 5 66 100 U 11.64 - 3 1.94 4.64 8.47 10 66 100 10 8.61 19.76 3,1 2.36 - 11.19 10 69 106 10,5 12.47 - I 3,2 2.03 5.05 9.60 10 69 106 11 12.97 - I 3,3 2.29 5.80 10.65 10 69 106 11,5 14.31 - I 3 A 2.51 - 11.48 10 73 112 12 16.29 P - I 3,5 2.21 8.32 9.76 10 73 112 12,5 16.29 P - 3,6 2.44 - 12.38 10 73 112 13 17.03 P - 3,7 2.58 - 11.84 10 73 112 14 21.19 - I 3,8 2.58 - 11.84 10 78 119 15 26.33 - I 2.81 - 11.93 10 78 119 16 31.48 - I 2.45 7.33 10.65 10 78 119 Deep-hole drill HSS FS TiAIN 11.84 12.28 13.91 13.12 15.30 15.15 18.77 15.80 17.28 20.30 20.30 24.85 30.20 23.56 27.03 28.81 43.16 44.35 34.75 49.30 54.05 66.33 68.51 71.87 mm 78 78 82 87 87 87 91 91 91 97 97 102 102 102 102 109 109 109 109 115 115 121 121 121 128 128 134 134 134 140 144 149 K mm 119 119 126 132 132 132 139 139 139 148 148 156 156 156 156 165 165 165 165 175 175 184 184 184 195 195 205 205 205 214 220 227 49