287 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.287

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 287 0287 ENG Lab2u

Hoffmann Group 47 HSS Co8 NR /w\ k12 L 1 30° h6 I DIN 1835 B Roughing end mill Relief ground knuckle form profile. End face recessed. Wide lands permit frequent regrinding without losing the profile. Advantage: For roughing at low cutting depths (predominantly face milling). Very reliable, due to lower load on the machine spindle. 192970 Suitable for/ vc m/min Alu plastics aQQo Alu cast > 10 % SI X <500N X < 750 N X <900N X < 1100 N X <1400 N X <55 HRC X < 60 HRC X <65 HRC X <67 HRC X <70 HRC INOX <900 N INOX >900 N GG(G CuZn Uni 4 6 ISO code nri N nri P H K rn 192970 83 28 23 23 12 23 55 0k12 Dc 192970 186.12 Naof teeth Z -1 i ti 0k12 Dc 192970 30 90 20 0.055 No. of teeth Z UB Roughing end mill L, L < 750 N Roughing end mill L, Lt mm f, mm 30 155.43 5 30 90 20 0.055 40 220.77 6 32 95 mm 25 < 750 N f, mm 0.055 HSS DIN K7 e8 u “RTl Co5 850 D/F W 1 - DIN 1835 B Woodruff keyseating cutter Peripheral cutting, alternate set teeth (staggered). The sides of the teeth are ground to give clearance and thus cannot jam in the component. Special surface treatment. Note: For milling Woodruff keyways to DIN 6888 or for milling small slots. 194010 Woodruff keyway Suitable for/ vc m/min Alu plastics Alu cast > 10 % SI X < 500 N X < 750 N X <900N X < 1100 N X <1400 N X <55 HRC X <60 HRC X <65 HRC X <67 HRC X <70 HRC INOX <900 N INOX >900 N GG(G) CuZn Uni 4 6 ISO code N P H K N 250 70 35 28 22 35 0xwidth hllxeS Be 10,5x2 10,5x2,5 10,5x3 13,5x2 13,5x2,5 13,5x3 13,5x4 16,5x2,5 16,5x3 16,5x4 16,5x5 19,5x3 19,5x4 19,5x5 22,5x4 22,5x5 22,5x6 nm Woodruff keyseating cutter Naof teeth Z for Woodruff keyways to DIN 6888 mm f i 1, m at m f j m > . m 31.48 6 2.0X3.7 50 6 31.48 6 2,5x3,7 50 6 31.48 6 3.0X3.7 50 6 30.00 10 2.0X5.0 56 10 30.00 10 2,5x5,0 56 10 30.00 10 3.0X5.0 56 10 30.00 10 4.0X5.0 56 10 32.67 10 2,5x6,5 56 10 32.67 10 3.0X6.5 56 10 32.67 10 4.0X6.5 56 10 32.67 10 5.0X6.5 56 10 38.21 10 3.0X7.5 56 10 38.21 10 4.0X7.5 56 10 38.21 10 5,0x7,5 63 10 44.95 10 4.0X9.0 63 10 44.95 10 5,0x9,0 63 10 44.95 10 6,0x9,0 63 10 < 750 N f, mm 0.045 0.045 0.045 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.08 0.08 0xwidth hl1xe8 Dc Is 194010 No. of teeth Z for Wood ruff keyways to DIN 6888 mm f i I, m ;ot m n r im Wood ruff keyseating cutter 48.81 10 5,0x10,0 63 10 48.81 10 6,0x10,0 63 10 48.81 10 7.0x10.0 63 10 48.81 10 8,0x10,0 63 10 57.42 10 5,0x11,0 63 10 57.42 10 6,0x11,0 63 10 57.42 10 7,0x11,0 63 10 57.42 10 8,0x11,0 63 10 66.92 12 5,0x13,0 71 12 66.92 12 6,0x13,0 71 12 66.92 12 8,0x13,0 71 12 97.81 12 7,0x15,0 71 12 97.81 12 8,0x15,0 71 12 97.81 12 9,0x15,0 71 12 97.81 12 10,0x15,0 71 12 120.78 12 10,0x16,0 71 12 < 750 N f, mm 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.09 0.09 0.09 0.09 0.09 0.09 0.09 0.09 287