270 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.270

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 270 0270 ENG Lab2u

Hoffmann Group 47 HSS Co8 DIN 844 B Type W e8 00 > 0 42° hT1 DIN 1835 B 4aBat M Slot drills Centre cutting edge geometry for plunging. Wide, fine ground chip flutes. Exceptionally fine component surface finish - due to precisely ground cutting edges. For slots or for milling pockets from the component centre. Note: Note Only for use in climb milling. 191100 Suitable for/ Alu Alu vc m/min < 500 N < 750 N <900N XXX < 1100 N < 1400 N <55 HRC X < 60 HRC X <65 HRC X <67 HRC X lNOX INOX < 70 HRC <900 N > 900 N Ti >S50N Graphite GRP CRP Uni a 6 ISO code P P P H N 1 191100 28 tsMUIIHIlJ Slot drill m L, Alu 0e8 D< nmi'iihh M Slot drill 1 Alu mm 2 20.30 7 51 6 0.006 7 24.35 16 66 10 0.011 mm 19.31 8 52 6 0.006 8 23.07 19 69 10 0.02 3 18.51 8 52 6 0.006 8,5 27.32 19 69 10 0.02 £S 21.19 10 54 6 0.006 9 30.10 19 69 10 0.02 19.31 11 55 6 0.008 10 28.12 22 72 10 0.029 4,5 23.07 11 55 6 0.008 12 32.27 26 83 12 0.041 5 19.76 13 57 6 0.008 14 43.56 26 83 12 0.041 23.76 13 57 6 0.008 16 46.83 32 92 16 0.046 19.76 13 57 6 0.011 18 59.00 32 92 16 0.046 6,5 27.32 16 66 10 0.011 20 73.46 38 104 20 0.055 DIN 844 B Type N e8 0 30° “sn DIN 1835 B Slot drills Centre cutting teeth for plunging. Eccentric relief ground. 191250- For very high demands on the metal removal rate. 191260 - Economy version. Note: Suitable for use as a slot drill (tolerance e8) or an end mill. 50 % higher metal removal rate than 2 flute slot drills. Larger flutes than multi-flute end mills (good for soft material). For milling keyways. HSS Co8 HSS HSS Co8 191200 i > 191250 I 191260 Suitable for/ v, m/min Alu plastics QSDCl, Alu cast > 10 % Si X < 500 N X < 750 N X <900N X < 1100 N X <1400 N X <55 HRC X <60 HRC X <65 HRC X <67 HRC X <70 HRC INOX < 900 N INOX > 900 N GG(G) CuZn Uni 4 ISO code nri Mn N P H K Mri 191200 83 28 23 23 23 55 191250 138 110 83 64 64 37 32 23 18 55 110 191260 120 78 55 55 17 46 92 O 0e8 Dc MfFTCT mSrm mmm jfoEarant Slot drills HSS-C08 I HSS-PM HQLSX. HSS-C08 mm TiAIN 1,5 10.45 2 10.45 20.69 11.52 B9 10.45 20.69 11.84 3 10.45 20.69 11.84 3,5 10.45 20.69 11.84 4 10.45 20.69 11.84 4,5 10.45 20.69 11.84 5 10.45 20.69 11.84 10.45 20.69 11.84 10.45 20.69 11.84 6,5 13.96 29.80 15.08 7 13.66 29.80 15.08 7,5 13.66 8 13.66 29.90 15.08 8,5 13.66 29.90 15.44 9 13.66 29.90 15.44 i SI mm 7 7 10 11 11 13 13 13 16 16 16 19 19 19 mm 51 51 52 52 54 55 55 57 57 57 66 66 66 69 69 69 mm 6 6 6 6 6 6 6 6 6 6 10 10 10 10 10 10 mm 0.002 0.003 0.003 0.003 0.003 0.005 0.005 0.005 0.005 0.007 0.007 0.007 0.007 0.01 0.01 0.01 jfoGaiant HOLCX. tS I, m Kt mm HSS-C08 HSS-PM HSS-C08 mm f, mm TiAIN 9,5 13.66 19 69 10 0.01 10 13.07 32.27 15.44 22 72 10 0.015 11 20.20 42.27 21.24 22 79 12 0.015 12 17.62 42.27 21.24 26 83 12 0.024 13 27.42 51.28 28.08 26 83 12 0.024 14 27.42 52.27 28.08 26 83 12 0.024 15 28.61 53.86 29.97 26 83 12 0.024 16 27.03 60.59 29.97 32 92 16 0.03 18 36.83 68.71 35.64 32 92 16 0.03 20 41.38 88.70 43.56 38 104 20 0.035 22 64.15 38 104 20 0.035 24 60.19 - 56.88 45 121 25 0.035 25 62.77 146.03 57.24 45 121 25 0.035 26 102.96 45 121 25 0.035 28 103.95 45 121 25 0.035 30 118.80 45 121 25 0.035 270