146 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.146

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 146 0146 ENG Lab2u

Hoffmann Group 47 HSS E-PM I'vMvfl I IStandatdl I DIN 13 ISO 2X 6HX i-4 i h6 I DIN 1835 B 1 1 <2.5xD 4asat M Synchronised through hole machine tap with internal coolant supply Sturdy design with spiral point and shank to DIN 1835-B. Special geometry for use on machines with synchronised spindle drives. The tap is controlled by the synchronising spindle of the machine, Special TiAIN coating for optimum tool life. For use with emulsion (fat content minimum II II 8%). Ip 13 2070 - With internal coolant supply for maximum tool life. table) by drilling the tapping hole 0 0.05 to 0.3 mm larger. Note: For use on synchronised spindles, the GARANT quick-change tapping chuck No. 338100- 8118 with minimum length adjustment (MLA) ensures highest process reliability. 132065 n 132070 The spiral point evacuates theswarfin the cutting direction. Suitable for/ v, m/min Alu plastics Alu cast >10MSi X < 500 N X < 750 N X < 900 N X < 1100N X < 1400 N X <55 HRC X < SO HRC X <65 HRC X <67 HRC X <70 HRC T00L0X- 33 HRC T00L0X- 44 HRC IN0X <900N IN0X >900N Ti > 850 N 6 ISO code N N Mm P H 132065/2070 37 35 22 12 7 7 6 132065 - 132070 Machine tap for synchronised spindles HSS-E-PM HSS-E-PM internal cooling TiAIN 27.62 - 35.64 35.64 87.32 35.64 87.32 43.26 94.64 51.08 102.96 68.11 120.78 96.62 162.86 fT mm 0.5 0.7 0.8 1 1.25 1.5 1.75 2 mm 6 6 6 6 8 10 12 12 jhiiaraii. Quick-change tapping heads for synchronised spindles mm 4.9 4.9 4.9 4.9 6.2 8 9 9 Outstandingly suitable for use with GARANT synchronous machine taps / fluteless taps No. 33 8100 - 8118 with Minimum Length Adjustment (MLA). MLA (length compensation tension 1 mm, compression 0.2 mm) compensates for difference in pitch between the machine tap/fluteless tap and synchronised spindle. This allows the tools to run at higher cutting speeds; the concentricity is significantly increased. mm 2.5 3.3 4.2 5 6.8 8.5 10.2 14 GARANT quick-change tapping heads No. 338055 - 8060 are recommended for GARANT synchronous machine taps / fluteless taps with internal coolant supply. These tapping heads also offer Minimum Length Adjustment (MLA) via a Minimum Quantity Lubrication system (MQL)- for very high process reliability and long tool life. Quick-change tapping head MLA No. 33 8100 with quick-change insert No. 33 8120. Quick-change tapping head MLA with MMS No. 33 8055 with quick-change insert No. 331065. Synchronous machine taps Synchronous machine taps Synchronous machine taps Synchronous fluteless taps 131125 131128(IC) 132950 132955 00 132065 132070(10 132280 132285(10 132740 132745 00 M 132555 132560(E) 132565 (10 M 134275 134280(10 134285(10 135290 MF 137180 137183(E) 137186(10 S 13 7344 137345(E) 137346(10 137810 137813(E) 137816(10 146