Сверла Митсубиси по металлу Японский осевой режущий инструмент для сверления отверстий DRILLING

Сверла Митсубиси по металлу Японский осевой режущий инструмент для сверления отверстий DRILLING

Сверла Митсубиси по металлу Японский осевой режущий инструмент для сверления отверстий DRILLING _ LU Q m O' 5 TAF JUST FIT SLEEVE JFS t When intstalling on the drill shank the rotation axis of the drill is slightly decentered. It enables slight enlargement of the machined hole, (enlargement range: 0.1-0.5mm) Обозначение Order Number Stock Set Обозначение Order Number DCB CON BD LF L5 lncrease (S5 2) MVX Обозначение Order Number The Last Three Letters JFS2520-10 JFS-1 20 25 33 43 30 0.1 F20 JFS2520-20 JFS-1 20 25 33 43 30 0.2 F20 JFS2520-30 JFS-1 20 25 33 43 30 0.3 F20 JFS2520-40 JFS-1 20 25 33 43 30 0.4 F20 JFS2520-50 JFS-1 20 25 33 43 30 0.5 F20 JFS322S-10 JFS-2 25 32 40 50 34 0.1 F25 JFS3225-20 JFS-2 25 32 40 50 34 0.2 F25 JFS3225-30 JFS-2 25 32 40 50 34 0.3 F25 JFS3225-40 JFS-2 25 32 40 50 34 0.4 F25 JFS3225-50 JFS-2 25 32 40 50 34 0.5 F25 JFS4032-10 JFS-3 32 40 48 55 40 0.1 F32 JFS4032-20 JFS-3 32 40 48 55 40 0.2 F32 JFS4032-30 JFS-3 32 40 48 55 40 0.3 F32 JFS4032-40 JFS-3 32 40 48 55 40 0.4 F32 JFS4032-50 JFS-3 32 40 48 55 40 0.5 F32 JFS5040-10 - 40 50 68 65 50 0.1 F40 JFS5040-20 - 40 50 68 65 50 0.2 F40 JFS5040-30 - 40 50 68 65 50 0.3 F40 JFS5040-40 - 40 50 68 65 50 0.4 F40 JFS5040-50 - 40 50 68 65 50 0.5 F40 It does not correspond to the shank diameter 050 mm. Guideline for Selecting a JUST FIT SLEEVE Increase Size of the increase in the cutting diameter. Desired = (Drill0+ Increase of JFS) + 0.1 mm (Eg.) Desired diameter is 20.3 mm (oversize is taken as 0.1 mm). 02O.3=(MVX2OOO X OF25+JFS3225-20)+0.1 I I 20 mm Drill Using JFS an Increase Oversize of 0.2 mm. (Note) Oversize can vary due to the cutting conditions used, please use the above as a guideline. Ordering the JUST FIT SLEEVE MVX MVX2000 X OF25 JUST FIT SLEEVE JFS JFS3225-20 Purchasing Method 1 Oversize can vary due to the cutting conditions used. Therefore it is recommended to purchase as a set. When placing an order, please use the set order number. (5 sleeves/set) Purchasing Method 2 It is possible to order individually. When placing an order, please use the order number. Inventory maintained in Japan. 1918 Mitsubishi Materials