Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ VFEXL Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Work material Hardened steel (45 55HRC) AISI H13 Hardened steel (55 62HRC) AISI D2 Dia. Dtynm) Neck length LU(mm Revolution niiH Feed rate (mmlmin) Depth of cut ap nm Revolution (mill4 Feednte ImmMn Depth of cut 0.1 0.5 40000 100 0.002 40000 80 0.001 0.2 0.6 40000 400 0.004 40000 360 0.004 1 40000 300 0.003 40000 250 0.002 1.5 40000 200 0.002 40000 150 0.001 0.3 1 40000 500 0.006 40000 450 0.004 2 40000 400 0.003 38000 350 0.002 3 38000 250 0.002 36000 200 0.001 0.4 1 40000 800 0.008 36000 500 0.006 2 40000 500 0.007 30000 350 0.005 4 36000 300 0.004 27000 200 0.003 0.5 2 40000 800 0.01 30000 600 0.009 4 36000 600 0.008 27000 450 0.007 6 30000 400 0.005 22000 300 0.004 0.6 2 40000 1000 0.015 30000 700 0.012 4 36000 800 0.01 27000 500 0.01 6 30000 600 0.006 22000 350 0.006 0.8 4 36000 1200 0.03 27000 900 0.02 6 30000 900 0.02 22000 650 0.015 8 24000 600 0.01 18000 450 0.008 10 20000 400 0.008 15000 300 0.005 1 4 32000 1600 0.05 24000 1100 0.04 6 32000 1400 0.04 24000 1000 0.03 8 28000 1000 0.03 21000 750 0.02 10 28000 800 0.02 21000 600 0.015 12 24000 500 0.02 18000 370 0.01 1.5 6 22000 1200 0.08 16000 900 0.06 8 22000 1100 0.07 16000 800 0.05 10 22000 1000 0.06 16000 750 0.04 12 20000 800 0.05 15000 600 0.03 16 18000 500 0.03 13000 350 0.02 2 6 16000 1000 0.15 12000 750 0.15 8 16000 1000 0.15 12000 750 0.1 10 16000 800 0.1 12000 600 0.08 12 16000 800 0.08 12000 600 0.06 16 15000 600 0.06 11000 450 0.05 20 14000 500 0.05 10000 350 0.04 3 12 11000 800 0.2 8200 600 0.15 16 11000 600 0.15 8200 450 0.15 20 11000 500 0.1 8200 350 0.1 DC "iaart ap H If the depth of cut is shallow, the revolution and feed rate can be increased. Cutting condition may be considerably different due to the overhang (milling depth), depth of cut, and machine tools. Please see the above table as a standard. 726 Mitsubishi Materials