1276 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.M120

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. M120 1276 Lab2u

INDEXABLE MILLING INDEXABLE MILLING DC (mm) RE (mm) Rampina Helical Millina (Blind Hole, Flat Bottom) Helical Milling (Through Hole) RMPX L (mm) DH max. (mm) P max. (mm) DH min. (mm) P max. (mm) DH min. (mm) P max. (mm) 0.2 1.56” 294 35 1.5 31.5 1.2 28.1 0.9 0.4 1.56" 294 34.6 1.4 31.5 1.2 28.1 0.9 18 0.8 1.56" 294 33.8 1.4 31.5 1.2 28.1 0.9 1 1.56" 294 33.4 1.3 31.5 1.2 28.1 0.9 1.2 1.56" 294 33 1.3 31.5 1.2 28.1 0.9 1.6 1.56" 294 32.2 1.2 31.5 1.2 28.1 0.9 0.2 1.35" 340 39 1.4 35.5 1.1 32 0.9 0.4 1.35" 340 38.6 1.4 35.5 1.1 32 0.9 20 0.8 1.35" 340 37.8 1.3 35.5 1.1 32 0.9 1 1.35" 340 37.4 1.3 35.5 1.1 32 0.9 1.2 1.35" 340 37 1.3 35.5 1.1 32 0.9 1.6 1.35" 340 36.2 1.2 35.5 1.1 32 0.9 0.2 1.16" 396 43 1.3 39.5 1.1 36 0.9 0.4 1.16° 396 42.6 1.3 39.5 1.1 36 0.9 22 0.8 1.16" 396 41.8 1.3 39.5 1.1 36 0.9 1 1.16“ 396 41.4 1.2 39.5 1.1 36 0.9 1.2 1.16° 396 41 1.2 39.5 1.1 36 0.9 1.6 1.16" 396 40.2 1.2 39.5 1.1 36 0.9 0.2 0.97” 473 49 1.3 45.5 1.1 42 0.9 0.4 0.97° 473 48.6 1.3 45.5 1.1 42 0.9 25 0.8 0.97” 473 47.8 1.2 45.5 1.1 42 0.9 1 0.97“ 473 47.4 1.2 45.5 1.1 42 0.9 1.2 0.97" 473 47 1.2 45.5 1.1 42 0.9 1.6 0.97" 473 46.2 1.1 45.5 1.1 42 0.9 0.2 0.84" 546 55 1.2 51.5 1.1 48 0.9 0.4 0.84" 546 54.6 1.2 51.5 1.1 48 0.9 28 0.8 0.84" 546 53.8 1.2 51.5 1.1 48 0.9 1 0.84“ 546 53.4 1.2 51.5 1.1 48 0.9 1.2 0.84” 546 53 1.2 51.5 1.1 48 0.9 1.6 0.84" 546 52.2 1.1 51.5 1.1 48 0.9 0.2 0.77” 596 59 1.2 55.5 1.1 52 0.9 0.4 0.77° 596 58.6 1.2 55.5 1.1 52 0.9 30 0.8 0.77” 596 57.8 1.2 55.5 1.1 52 0.9 1 0.77° 596 57.4 1.2 55.5 1.1 52 0.9 1.2 0.77° 596 57 1.1 55.5 1.1 52 0.9 1.6 0.77” 596 56.2 1.1 55.5 1.1 52 0.9 0.2 0.71” 646 62.8 1.2 59.4 1.1 56 0.9 0.4 0.71" 646 62.4 1.2 59.4 1.1 56 0.9 32 0.8 0.71" 646 61.6 1.2 59.4 1.1 56 0.9 1 0.71" 646 61.2 1.1 59.4 1.1 56 0.9 1.2 0.71" 646 60.8 1.1 59.4 1.1 56 0.9 1.6 0.71" 646 60 1.1 59.4 1.1 56 0.9 0.2 0.63” 728 69 1.2 65.5 1.1 62 0.9 0.4 0.63° 728 68.6 1.2 65.5 1.1 62 0.9 35 0.8 0.63” 728 67.8 1.1 65.5 1.1 62 0.9 1 0.63" 728 67.4 1.1 65.5 1.1 62 0.9 1.2 0.63" 728 67 1.1 65.5 1.1 62 0.9 1.6 0.63' 728 66.2 1.1 65.5 1.1 62 0.9 0.2 0.54° 849 78.8 1.2 75.4 1 72 0.9 0.4 0.54° 849 78.4 1.1 75.4 1 72 0.9 40 0.8 0.54° 849 77.6 1.1 75.4 1 72 0.9 1 0.54° 849 77.2 1.1 75.4 1 72 0.9 1.2 0.54” 849 76.8 1.1 75.4 1 72 0.9 1.6 0.54° 849 76 1.1 75.4 1 72 0.9 0.2 0.42° 1092 98.8 1.1 95.4 1 92 1 0.4 0.42” 1092 98.4 1.1 95.4 1 92 1 50 0.8 0.42“ 1092 97.6 1.1 95.4 1 92 1 1 0.42“ 1092 97.2 1.1 95.4 1 92 1 1.2 0.42" 1092 96.8 1.1 95.4 1 92 1 1.6 0.42" 1092 96 1.1 95.4 1 92 1 0.2 0.32" 1433 124.8 1.1 121.4 1 118 1 0.4 0.32' 1433 124.4 1.1 121.4 1 118 1 63 0.8 0.32" 1433 123.6 1.1 121.4 1 118 1 1 0.32' 1433 123.2 1.1 121.4 1 118 1 1.2 0.32' 1433 122.8 1.1 121.4 1 118 1 1.6 0.32“ 1433 122 1 121.4 1 118 1 Note 1) When machining a highly ductile work material with the ramping angles in the table above, chips may be elongated. Shows the distance until a maximum depth of cut of 8 mm is achieved at the maximum ramping angle L (= 8/tan a). M120