735 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J113

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J113 0735 Lab2u

CARBIDE RECOMMENDED CUTTING CONDITIONS Side milling Work Material Carbon steel, Cast iron, Alloy steel (-30HRC) AIS11050, AISI No 35 B, AISI P20 Alloy steel, Tool steel, Pre-hardened steel AISI H13, AISI W1-10, AISI P21 Austenitic stainless steel, Titanium alloy AISI 304, AISI 306, Ti-6AI-4V Heat resistant alloys lncone 718 Dia. DC (mm) Revolution (min'1) Feed rate (mm/min) 1 19000 600 13000 310 10000 200 9500 65 1.5 14000 600 9000 310 7500 210 6400 75 2 11000 600 7200 310 6000 210 4800 75 3 8500 770 5300 380 4400 220 3200 100 4 7200 850 4400 480 3700 250 2400 130 6 5300 940 3200 490 2700 270 1600 130 8 4000 1010 2400 560 2000 280 1200 120 10 3200 1000 1900 480 1600 300 950 110 12 2700 950 1600 440 1300 300 800 90 16 2000 720 1200 350 1000 260 600 70 20 1600 600 1000 290 800 240 480 60 Depth of cut 0.2DC (DC>03) 0.1 DC (DC<03) 0.05DC 1 1 S1.5DC 1 1.5DC IPIunging Work Material Carbon steel, Cast iron, Alloy steel (-30HRC) AIS11050, AISI No 35 B, AISI P20 Alloy steel, Tool steel, Pre-hardened steel AISI H13, AISI W1-10, AISI P21 Austenitic stainless steel, Titanium alloy AISI 304, AISI 306, Ti-6AI-4V Dia. DC (mm) Revolution (min'1) Feed rate (mm/min) 1 13000 80 10000 50 6000 10 1.5 12000 120 8000 80 6000 20 2 11000 200 7200 140 6000 30 3 8500 250 5300 180 4200 50 4 7200 300 4400 210 3300 60 6 5300 300 3200 210 2200 70 8 4000 320 2400 220 1600 80 10 3200 340 1900 240 1300 70 12 2700 320 1600 220 1100 70 16 2000 250 1200 180 800 55 20 1600 200 1000 140 640 55 Depth of cut F Tsdc (DC> ) i„ 'i 10.5DC (DC ) i a.2DC (DC 02) DC:Dia. DC: Dia. m /> 2 Q DC DC LlI a. LU DC DC m o I Slotting Work Material Carbon steel, Cast iron, Alloy steel (-30HRC) AIS11050, AISI No 35 B, AISI P20 Alloy steel, Tool steel, Pre-hardened steel AISI H13, AISI W1-10, AISI P21 Austenitic stainless steel, Titanium alloy AISI 304, AISI 306, Ti-6AI-4V Heat resistant alloys lnconel718 Dia. DC (mm) Revolution (min'1) Feed rate (mm/min) 1 13000 130 10000 80 6000 30 5700 25 1.5 12000 250 8000 150 6000 60 3800 30 2 11000 500 7200 260 6000 130 2800 35 3 8500 640 5300 320 4200 130 1900 50 4 7200 650 4400 370 3300 140 1400 70 6 5300 720 3200 380 2200 140 950 70 8 4000 780 2400 430 1600 140 720 60 10 3200 770 1900 370 1300 150 570 50 12 2700 730 1600 340 1100 150 480 40 16 2000 600 1200 290 800 130 360 30 20 1600 500 1000 240 640 120 290 25 Depth of cut 1DC(DC>02) 0.SDC(DC< 2) 0.5DC(DC> 2) S0.2DC(DC< 2) 0.2DC o 3 o DC O in DC:Dia. Note 1) When cutting austenitic stainless steels, the use of water-soluble cutting fluid is effective. Note 2) If the depth of cut is shallow, the revolution and feed rate can be increased, Note 3) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. J113