677 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J055

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J055 0677 Lab2u

CARBIDE RECOMMENDED CUTTING CONDITIONS Work Carbon steel, Cast iron, Alloy steel (-30HRC) Alloy steel, Tool steel, Pre-hardened steel Austenitic stainless steel, Titanium alloy Hardened steel (45 55HRC) Material AIS11050, AISI No 35 B, AISI P20 AISI H13, AISI W1-10, AISI P21 AISI 304, AISI 306, Ti-6AI-4V AISI H13 Dia. DC (mm) Revolution (mln'1) Feed rate (mm/min) Revolution (min'1) Feed rate (mm/min) 0.1 40000 - (40) 40000 - (40) 40000 - (35) 40000 - (25) 0.2 40000 - (45) 40000 - (45) 40000 - (35) 32000 - (25) 0.3 40000 - (55) 32000 - (45) 27000 - (35) 21000 - (25) 0.4 32000 - (60) 24000 - (45) 20000 - (35) 16000 - (25) 0.5 25000 - (60) 19000 - (45) 16000 - (35) 13000 - (25) 0.6 21000 - (60) 16000 - (45) 13000 - (35) 11000 - (25) 0.7 18000 - (60) 14000 - (45) 11000 - (35) 9100 - (25) 0.8 16000 - (60) 12000 - (45) 9900 - (35) 8000 - (25) 0.9 14000 - (60) 11000 - (45) 8800 - (35) 7100 - (25) 1 13000 60 (60) 9500 45 (45) 8000 35 (35) 6400 25 (25) 1.5 8500 60 (60) 6400 45 (45) 5300 35 (35) 4200 25 (25) 2 6400 60 (60) 4800 45 (45) 4000 35 (35) 3200 25 (25) 2.5 5100 60 (60) 3800 45 (45) 3200 40 (40) 2500 25 (25) 3 4200 65 (60) 3400 55 (45) 2600 40 (40) 2100 25 (25) 4 3400 80 (60) 2700 65 (45) 2100 (1600) 50 (30) 1700 35 (25) 5 2900 100 (60) 2300 80 (45) 1800 (1350) 60 (30) 1500 40 (25) 6 2500 120 (60) 2000 100 (50) 1500 (1100) 75 (30) 1300 50 (25) 8 1900 130 (60) 1500 100 (50) 1200 (900) 80 (30) 1000 50 (25) 10 1600 130 (60) 1300 100 (50) 950 (710) 75 (30) 800 50 (25) 12 1300 120 (60) 1100 100 (50) 800 (600) 75 (30) 670 50 (25) Depth of cut 0.05DC (MAX. 0.5mm) 2.5 DC SJ.02DC (DC< 0.5) O.O5DC(tfO.500.5) ( ): Indicates standard revolution and feed rate for slotting. DCiDia. o in Note 1) When cutting austenitic stainless steels, the use of water-soluble cutting fluid is effective. Note 2) If the depth of cut is shallow, the revolution and feed rate can be increased, Note 3) When drilling, please set the feed rate at 1/3 or below the values above. Note 4) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. J055 ROUGHING BARREL TAPER RADIUS BALL