437 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.F013

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. F013 0437 Lab2u

Reference Material C-TYPE CIRCLIP STANDARDS LIST Category Application Standard Width (Tolerance) For shaft For hole C-type stop ring CO) For shaft C-type concentric stop ring For shaft E-type stop ring For shaft For hole For hole ANSI B27.7/27.8 (US) BS 3673 (UK) DIN 471/472 (De) NF E 22 163 (Fr) UNI 7435/7438 (It) JIS B2804(JP) 0.5 0.7 0.8 0.9 1.1 1.3 1.6 1.85 N1 American 2.15 2.65 3.15 4.15 5.15 6.2 0.7 1.0 1.2 1.4 +0.14 0 +0.18 0 +0.22 0 0.305 0.457 +0.051 0 0.737 0.991 1.168 +0.076 0 1.422 1.727 +0.102 0 2.184 +0.127 0 2.616 3.048 3.531 +0.152 0 1.15 1.35 1.75 1.95 +0.14 0 2.2 2.7 3.2 4.2 +0.18 0 9 1.1 1.3 1.6 1.85 2.15 2.65 3.15 4.15 5.15 6.2 +0.14 0 +0.18 0 +0.22 0 0.457 +0.051 0 0.737 0.991 1.168 +0.076 0 1.422 1.727 I 2.184 +0.102 0 2.616 3.048 +0.127 0 0.32 0.5 +0.05 0 +0.10 0 +0.14 0 0.305 0.457 0.584 +0.051 0 0.3 0.4 0.5 +0.05 0 0.737 0.991 1.168 +0.076 0 0.7 0.9 +0.10 0 1.15 1.75 +0.14 0 1.422 +0.102 0 1.727 I 2.2 O-RING STANDARDS Category Standard General Width (Tolerance) For oil pressure For air pressure For stable For dynamic DIN 3770/3771 (De) JIS B 2401 (JP) ISO 3601 SMS 1586/1588 (Se) BS 1806/4518 (UK) 2.54 I 3.18 4.32 6.1 8.0 3.2 4.0 +0.2 7.5 0 11.0 I 2.39 3.58 I 4.78 7.14 9.58 +0.13 0 2.5 3.2 4.7 7.5 11.1 +0.25 0 +0.14 0 1.9 2.3 2.9 3.6 4.5 5.5 7.0 8.6 10.7 +0.1 0 +0.15 0 +0.2 0 +0.3 0 +0.4 0 +0.5 0 2.3 +0.2 0 3.1 3.7 6.4 9.0 Cm 3.6 I 4.8 7.1 9.5 +0.25 0 2.3 I 31 3.7 6.4 9.0 +0.2 0 I 2.2 3.4 I 4.6 6.9 9.3 +0.25 0 H G-class insert with MF breaker is available for single-step machining. H Conventional GY series insert is available for single-step machining. Machined in multiple steps or by cross feed machining. L DIMENSION TOLERANCE CONVERSION TABLE Cutting Width CW (mm) 1 Dimensions L (mm) 2 Dimensional tolerance (mm) versus standard dimension (L) of each breaker GU GS/GM MS/MM R/L-GM Flat Top MF BM 1.50 14.70 0 2.00 20.70 0 0 0 0.10 0 0.35 0.20 2.24 3 (20.7) 0.35 2.39 20.70 0 0 0 0.35 2.50 20.70 0 0 0 0.125 0 0.35 0.20 2.74 3 (20.7) 0.35 3.00 20.70 0 0 0 0.15 0 0.35 0.20 3.18 20.70 0 0 0 0.35 0.20 3.24 3 (20.7) 0.35 4.00 25.65 0 0 0 0.20 0 0.30 0.15 4.24 3 (25.65) 0.30 4.75 25.65 0 0 0 0.30 0.15 5.00 25.65 0 0 0 0.30 0 0.30 0.15 5.24 3 (25.65) 0.30 6.00 25.65 0 0 0 0 0.30 0.25 6.31 3 (25.65) 0.30 6.35 25.65 0 0 0.30 0.25 8.00 30.50 0 0 0.30 1 This value is used at the described holder dimension. 2 when there is no applicable breaker. 3 The standard dimensions shown here use an approximate insert width.