Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ VOMHV General purpose cutting conditions Work material Carbon steel, Alloy steel, Mild steel AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic Stainless steels, Titanium alloys AISI 304, AISI 316, Ti-6AI-4V Dil Cling speed Revoluiien Feed rate Depth of cut Cutting speed Revdution Feed nte Depth of cut Cling speed Revdution Feed nte Depth of cut DCH (m/min (liit1 (mmlmin) (m/min (miir1 (rnn/min ip(mm (mtnin (miir1 (mmtnii ipfinm 2 100 16000 550 2 80 13000 270 2 60 9500 250 2 3 100 11000 670 3 80 8500 310 3 60 6400 250 3 4 100 8000 840 4 80 6400 410 4 60 4800 280 4 5 100 6400 840 5 80 5100 410 5 60 3800 280 5 6 100 5300 840 6 80 4200 440 6 60 3200 300 6 8 100 4000 740 8 80 3200 420 8 60 2400 320 8 10 100 3200 680 10 80 2500 360 10 60 1900 350 10 12 100 2700 570 12 80 2100 330 12 60 1600 340 12 16 100 2000 480 12 80 1600 300 12 60 1200 250 12 20 100 1600 380 12 80 1300 240 12 60 950 200 12 25 100 1300 340 12 80 1000 180 12 60 760 160 12 Work material Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631, 15-5PH, 17-4PH Copper, Copper alloys Heat resistant alloys lnconel718 Die. DC mm Cling speed (m/min Revolution (miir1 Feed nte (mmlmin) Depth of cut ni Cutthg spied (m/min Revdution (miir1 Feed nte (mmlmin Ihpthofcut p(mm Cling spiid (minin Rivdution (miir1 Fied nte (mmlmh Dipth of cut ipfmm 2 50 8000 170 1 120 19000 650 2 25 4000 74 0.6 3 50 5300 200 1.5 120 13000 790 3 25 2700 86 0.9 4 50 4000 250 2 120 9500 1000 4 25 2000 93 1.2 5 50 3200 250 2.5 120 7600 1000 5 25 1600 95 1.5 6 50 2700 290 3 120 6400 1000 6 25 1300 96 1.8 8 50 2000 260 4 120 4800 890 8 25 990 100 2.4 10 50 1600 230 5 120 3800 800 10 25 800 120 3 12 50 1300 210 6 120 3200 680 12 25 660 110 3.6 16 50 990 180 8 120 2400 570 12 25 500 84 4.8 20 50 800 150 10 120 1900 450 12 25 400 68 6 25 50 640 120 12 120 1500 400 12 25 320 50 7.5 DC tap MBS SMART MIRACLE Coating is not energized because of its nature. Therefore, an external contact (voltaic type) tool setter cannot be used. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. If the depth of cut is shallow, the revolution and feed rate can be increased. Mitsubishi Materials 829 Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide