Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ gMS Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS (): Indicates standard feed rate for slotting. Work material Structural steel. Carbon steel AIS11045, AIS11050 Carbon steel, Alloy steel (20 30HRC) AIS11055, AISI P20 Alloy steel, Tool steel, Pre-hardened steel (30 35HRC) AISI H13 Austenitic stainless steel AISI 304, AISI 316 Cast iron AISI No 35 B Aluminium alloy Oil. Million Feed rite Revdutitn Feed rate Revdution Feed nte Revdution Feed nte Revolution Feed rate Mufim Feed rate DC(mm) (mir'l (mn/min) (miir1) (mm/min (miir1 (mmlmin (miir' (mmJmin (miir' (imMn miir' mm/min 1 5300 65(50) 4200 40(30) 3000 30(25) 2400 22(18) 4500 70(55) 11000 140(110) 2 3100 70(55) 2600 50(40) 1800 40(30) 1400 25(20) 2700 75(60) 6800 160(130) 3 2300 75(60) 1800 55(45) 1400 45(35) 1100 30(25) 2000 80(65) 4800 200(160) 4 1800 85(70) 1400 60(50) 1100 45(35) 850 30(25) 1600 90(70) 3800 260(210) 5 1600 95(75) 1200 75(60) 900 50(40) 710 35(25) 1300 100(80) 3200 300(240) 6 1400 100(80) 1000 75(60) 780 55(45) 610 40(30) 1100 110(90) 2800 330(260) 8 1100 110(90) 800 80(65) 580 55(45) 470 40(30) 850 115(90) 2200 380(300) 10 860 120(95) 640 85(70) 470 55(45) 380 45(35) 700 130(105) 1800 360(290) 12 720 110(90) 530 80(65) 390 50(40) 310 40(30) 580 115(90) 1600 350(280) 16 540 95(75) 400 75(60) 300 45(35) 230 35(28) 440 100(80) 1200 290(230) 20 430 80(65) 320 60(50) 240 38(30) 190 30(25) 350 85(70) 960 250(200) 25 350 70(55) 250 50(40) 190 32(25) 150 25(20) 285 75(60) 760 220(180) 30 290 65(50) 210 45(35) 160 28(22) 120 22(18) 240 70(55) 640 200(160) 40 210 50(40) 150 30(25) 120 22(18) 90 18(15) 180 55(45) 480 160(130) 50 160 40(30) 115 28(22) 90 20(15) 70 15(12) 140 45(35) 380 130(105) 60 130 35(28) 95 25(20) 75 18(15) 55 12(10) 115 40(30) 310 110(90) <0.1DC (DC< 3) <0.2DC (DC >03) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. Mitsubishi Materials 1157 Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE