Фрезы Mitsubishi со сменными режущими пластинами INDEXABLE MILLING

Фрезы Mitsubishi со сменными режущими пластинами INDEXABLE MILLING

Фрезы Mitsubishi со сменными режущими пластинами INDEXABLE MILLING _ AXD4000 Cutting Speed Обрабатываемые материалы Work Material Greade Breaker Cutting Speed vc (mm/min) Q Mild Steel (ASTM A36,AIS11010) <180HB MP6120 GM 200 (150-220) Carbon Steel, Alloy Steel (AISI 1045,AISI 4140) 180 280HB MP6120 GM 200 (150-220) TF15 GL 1000 (200-3000) Aluminium Alloy Si<5% LC15TF (A6061, A7075 etc) TF15 MP9120 GM 1000 (200-3000) Aluminium Alloy (AC4B, ADC12, A390 etc) 5% Si 10% Si>10% MP9120 GM 1000 (200-3000) Ll Titanium Alloy (Ti-6AI-4V etc) MP9120 GM 40 (30-60) Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Breaker Cutting Width Depth of Cut Подача на зуб Feed per Tooth (mm/t.) Обрабатываемые материалы Work Material ae (mm) ap (mm) Cutting Edge Diameter DC 20 25,28 32,35 40 50, 63, 80 100,125 B <5 <0.05 <0.15 <0.15 <0.18 <0.18 <0.18 <0.25 DC < 10 <0.05 <0.12 <0.12 <0.15 <0.15 <0.15 < 14.5 <0.05 <0.10 <0.10 <0.12 <0.12 Mild Steel (ASTM A36, AIS11010) <5 <0.05 <0.12 <0.15 <0.15 <0.18 <0.18 <180HB GM <0.5 DC < 10 - <0.10 <0.12 <0.12 <0.15 <0.15 < 14.5 <0.08 <0.10 <0.10 <0.12 <0.75 DC <5 <0.05 <0.12 <0.12 <0.15 <0.15 <0.15 < 10 <0.10 <0.10 <0.12 <0.12 <0.12 DC (Slot) <5 <0.05 <0.10 <0.12 <0.12 <0.15 <0.15 <5 <0.05 <0.15 <0.15 <0.18 <0.18 <0.18 <0.25 DC < 10 <0.05 <0.12 <0.12 <0.15 <0.15 <0.15 < 14.5 <0.05 <0.10 <0.10 <0.12 <0.12 Carbon Steel, Alloy Steel (AISI 1045,AISI 4140) <5 <0.05 <0.12 <0.15 <0.15 <0.18 <0.18 180 280HB GM <0.5 DC < 10 <0.10 <0.12 <0.12 <0.15 <0.15 < 14.5 <0.08 <0.10 <0.10 <0.12 0.75 DC <5 <0.05 <0.12 <0.12 <0.15 <0.15 <0.15 < 10 - <0.10 <0.10 <0.12 <0.12 <0.12 DC (Slot) <5 <0.05 <0.10 <0.12 <0.12 <0.15 <0.15 (Note 1) The above cutting conditions are determined based on high workpiece and machine rigidity, where no vibration occurred. If vibrations occur make adjustments according to the machining conditions. (Note 2) Note, vibrations may occur in the following conditions. When using long tool overhang. When pocket machining corner radii. When the workpiece has poor clamping rigidity or when the machine rigidity or workpiece rigidity is low, vibrations can occur easily, if so, reduce cutting conditions such as width and depth of cut and feed per tooth. 1464 Mitsubishi Materials