Фрезы Mitsubishi со сменными режущими пластинами INDEXABLE MILLING

Фрезы Mitsubishi со сменными режущими пластинами INDEXABLE MILLING

Фрезы Mitsubishi со сменными режущими пластинами INDEXABLE MILLING _ WSX445 Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Wet Cutting Обрабатываемые материалы Work Material Hardness 1st Recommendation 2nd Recommendation vc (m/min) Finish Cutting fz ap P L Breaker Mild Steel < 180HB MP6120 VP15TF 150 (100-200) 0.15(0.1-0.2) < 1.0 MP6130 VP20RT 150 (100-200) 0.15(0.1-0.2) < 1.0 Carbon Steel 180 350HB MP6120 VP15TF 120(80-160) 0.15(0.1-0.2) < 1.0 Alloy Steel MP6130 VP20RT 120(80-160) 0.15 (0.1-0.2) 1.0 Alloy Tool Steel < 350HB MP6120 VP15TF 120(80-160) 0.15 (0.1-0.2) 1.0 (annealing) MP6130 VP20RT 120(80-160) 0.15(0.1-0.2) < 1.0 Pre-Hardened Steel 35 45HRC MP6120 VP15TF 100 (80-120) 0.15(0.1-0.2) < 1.0 MP6130 VP20RT 100 (80-120) 0.15(0.1-0.2) < 1.0 M L Breaker Austenitic Stainless Steel < 200HB MP7130 VP15TF 130(80-180) 0.15 (0.1-0.2) 1.0 MP7140 VP20RT 130(80-180) 0.15(0.1-0.2) < 1.0 Austenitic Stainless Steel > 200HB MP7130 VP15TF 100(80-150) 0.15(0.1-0.2) < 1.0 MP7140 VP20RT 100(80-150) 0.15(0.1-0.2) < 1.0 Two-phase Stainless Steel < 280HB MP7130 VP15TF 100(80-150) 0.15 (0.1-0.2) < 1.0 MP7140 VP20RT 100(80-150) 0.15 (0.1-0.2) 1.0 Precipitation Hardening < 450HB MP7130 VP15TF 90(50-140) 0.15 (0.1-0.2) < 1.0 Stainless Steel MP7140 VP20RT 90(50-140) 0.15 (0.1-0.2) 1.0 K L Breaker Gray Cast Iron £ 350MPa MC5020 - 180 (160-200) 0.15(0.1-0.2) < 1.0 VP15TF VP20RT 130 (100-160) 0.15 (0.1-0.2) 1.0 Ductile Cast Iron < 450MPa MC5020 - 180 (160-200) 0.15 (0.1-0.2) 1.0 VP15TF VP20RT 130 (100-160) 0.15(0.1-0.2) < 1.0 Ductile Cast Iron 800MPa MC5020 - 180 (160-200) 0.15(0.1-0.2) < 1.0 VP15TF VP20RT 110(80-140) 0.15(0.1-0.2) < 1.0 N L Breaker Aluminum Alloy - TF15 - > 300 0.15(0.1-0.2) < 1.0 S L Breaker Titanium Alloy MP9120 VP15TF 50 (40-60) 0.05(0.05-0.1) < 1.0 MP9130 VP20RT 50 (40-60) 0.05(0.05-0.1) < 1.0 Heat Resistant Alloy MP9120 VP15TF 40 (20-50) 0.05(0.05-0.1) < 1.0 MP9130 VP20RT 40 (20-50) 0.05(0.05-0.1) < 1.0 Refer to the table above and set the cutting conditions to match the application. Wet cutting is recommended, when focusing on the surface finish. (Life is lower than dry cutting.) 1372 Mitsubishi Materials