1070 Каталог HOFFMANN GROUP 2015 Инструмент режущий слесарный измерительный Стр.1070

Каталог HOFFMANN GROUP 2015 Tools Инструменты Ver 46 Стр. 1070 1070 ENG Lab2u

1 Carbide granules disc Stone working Version Steel disc with brazed-on carbide grit. Very long working lives and extremely high metal removal rates; medium grit. Application Grinding, correcting, trimming GFRP, calcareous sandstone, plaster board, aerated concrete, rubber. Also for smoothing rough formwork edges on exposed concrete. Note Not for use on metal. Work with low contact force. Avoid impact loads. Maximum speed 63 m/s (10,500 rpm). Disc 0 mm 115 K 56 9610 Carbide granules disc Diamond grinding disc for dry grinding Version Application Robust thin steel disc with brazed diamond segments, which are bedded in a special material. High removal rate, extremely long working life with low vibration (clean surfaces), for dry grinding. For grinding, correcting, smoothing of stone and concrete using angle grinders. Optimum speed 10,000 - 12,000 rpm. Maximum speed 15,000 rpm. Disc 0 mm 100 125 l_ m Q/iAn tfflflltt Diamond cutting disc 30 mu PREMIUM for stone tTHOlIl Stone cutting disc STANDARD Version Universal stone cutting disc (specification C30-BF). Application For natural and synthetic stone, refractory stone, and concrete. Disc 0 mm 115 125 178 230 j- r c Q7AA gflOUl Cutting disc - 56 9700 STANDARD for stone 25 Disc thickness mm 2.5 2.5 3 3 Shape description swan necked flat 9 22,23mm 80 m/s I tyfloiu Diamond cutting discs for wet and dry cutting P 1 22,23mm 80 m/s Version Diamond cutting discs for wet and dry cutting. Bore 0 22.23 mm. High cutting performance of the diamonds results in short cutting times. Extremely long working life, fewer disc changes. Unvarying diameter, always cuts to the full depth. Hardly any disc wear, reducing dust creation. 56 9720- For everyday use on all building materials such as concrete, bricks, natural stone etc. Directly sintered coating, hardened body (no wandering). 56 9740- High-performance with 10 or 12 mm coating height. Suitable for all building materials, long working life, protected against overheating. 56 9735 - Maximum performance and working life due to new segment technology with optimised grit distribution. 20 - 30 faster cutting with less vibration and clean cut edges. For general-purpose use on concrete, granite, abrasive materials, and steel. Coating height 14 mm. 56 9730- Extremely free-cutting, for short cutting times, reduced load on the machine and clean cuts. Protected against overheating. Extra thin, coating thickness 1.2 mm (0 115/125) and 1.9 mm (0 180 / 230). 56 9750- Tile disc with continuous cutting edge, disc thickness 1.2 mm, very free-cutting geometry, 10 mm coating width. Especially for tiles and granite slabs. 56 9770- Masonry cutting disc, cannot overheat, always replace in pairs. Application For cutting all common building materials such as concrete (even reinforced), bricks, natural stone, tiles, ceramics, steel etc. Note i Diamond coating already pre-sharpened. Observe correct direction of rotation i Other diamond cutting discs on request. Disc 0 mm 115 125 150 180 230 Is 56 9720 ABOUT Diamond cutting disc STANDARD Universal S 56 9740 ABOUT Diamond cutting disc PREMIUM high performance k 56 9735 ABOUT Diamond cutting disc 4 in 1 PREMIUM Premium k 56 9730 tfHOlP Diamond cutting disc STANDARD Fast Cut k 56 9750 tfHOlP Diamond cutting disc PREMIUM tiles k 56 9770 tfHOUt Diamond cutting disc PREMIUM masonry cutting disc 56 9770J 50 ; Masonry disc \ tfBOlIT Dressing stick for diamond cutting discs S 7ijS Application Cut a thin slice from the end of the dressing stick, working dry. This removes the TjVjS>j=j outer layer of blunt diamonds and uncovers a fresh layer of sharp diamonds. MB’ LxWxH mm >; Q7on tfflOUr Dressing stick for 25 diamond cutting discs 320X55X25 1070 Main catalogue Hoffmann Group 46