881 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J259

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J259 0881 Lab2u

CARBIDE Work Material Carbon steel, Alloy steel (180 280HB) Alloy Tool Steel (<350HB) Pre-hardened steel (35 45HRC) AIS11045, AISI 4140, SKD, SKT, AISI 4140, AISI P21 Hardened steel (45-52HRC) AISI H13, AISIL6 Copper, Copper alloys R RE (mm) Taper angle one side BHTA2 Neck length LB2 (mm) Revolution (min-1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) Revolution (min-1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) Revolution (min-1) Feed rate (mm/min) Depth of cut ap (mm) Depth of cut ae (mm) R2.0 0.5° 30 14000 2100 0.23 0.74 11000 1800 0.22 0.7 11000 1800 0.44 1.41 40 12000 1800 0.19 0.61 10000 1600 0.18 0.58 10000 1600 0.36 1.15 60 9000 1300 0.06 0.19 8500 1400 0.07 0.21 8500 1400 0.16 0.5 1 20 15000 2700 0.31 0.99 12000 2200 0.3 0.96 12000 2200 0.72 2.3 30 14000 2100 0.23 0.74 11000 1800 0.22 0.7 11000 1800 0.53 1.69 35 12000 1800 0.21 0.67 10000 1700 0.2 0.64 10000 1700 0.48 1.54 40 12000 1700 0.19 0.61 10000 1600 0.18 0.58 10000 1600 0.43 1.38 45 12000 1500 0.13 0.42 10000 1600 0.12 0.38 10000 1600 0.29 0.92 66 9000 1100 0.08 0.24 8500 1300 0.07 0.21 8500 1300 0.16 0.5 1.5° 50 12000 2200 0.11 0.35 10000 1700 0.1 0.32 10000 1700 0.24 0.77 84 8000 1400 0.04 0.13 6500 900 0.03 0.1 6500 900 0.07 0.23 3° 30 14000 2500 0.23 0.74 11000 2000 0.22 0.7 11000 2000 0.53 1.69 45 11000 1900 0.16 0.51 9000 1600 0.15 0.48 9000 1600 0.36 1.15 R2.5 1" 38 10000 2200 0.28 0.9 8500 2000 0.27 0.86 8500 2000 0.65 2.07 50 9000 1900 0.24 0.77 8000 1800 0.23 0.74 8000 1800 0.55 1.77 65 8000 1600 0.16 0.51 6500 1400 0.15 0.48 6500 1400 0.36 1.15 1.5" 66 8000 1600 0.16 0.51 6500 1500 0.15 0.48 6500 1500 0.36 1.15 3" 36 10000 2700 0.31 0.99 8500 2300 0.3 0.96 8500 2300 0.72 2.3 R3.0 1 40 8000 2200 0.28 0.9 7500 2100 0.27 0.86 7500 2100 0.65 2.07 50 8000 2000 0.23 0.74 6500 1800 0.22 0.7 6500 1800 0.53 1.69 73 7000 1700 0.15 0.48 6500 1700 0.14 0.45 6500 1700 0.34 1.07 90 6500 1500 0.09 0.29 6000 1300 0.08 0.26 6000 1300 0.19 0.61 1.5" 53 7000 2100 0.22 0.7 6500 1900 0.21 0.67 6500 1900 0.5 1.61 3' 32 9000 2400 0.35 1.12 8000 2200 0.34 1.09 8000 2200 0.82 2.61 R4.0 1" 50 6000 2200 0.41 1.31 5500 2000 0.4 1.28 5500 2000 0.96 3.07 65 6000 2000 0.36 1.15 5200 1700 0.35 1.12 5200 1700 0.84 2.69 76 6000 1800 0.29 0.93 5000 1500 0.28 0.9 5000 1500 0.67 2.15 90 5000 1400 0.19 0.61 4700 1200 0.18 0.58 4700 1200 0.43 1.38 1.5" 40 6000 2300 0.46 1.47 5800 2200 0.45 1.44 5800 2200 1.08 3.46 56 6000 2200 0.38 1.22 5500 2000 0.37 1.18 5500 2000 0.9 2.84 3’ 35 7000 2700 0.49 1.57 6000 2400 0.48 1.54 6000 2400 1.15 3.69 R5.0 1" 60 5500 2600 0.51 1.63 4500 2300 0.5 1.6 4500 2300 1.2 3.84 70 5500 2600 0.46 1.47 4500 2200 0.45 1.44 4500 2200 1.08 3.46 100 5000 2400 0.36 1.15 4000 1900 0.35 1.12 4000 1900 0.84 2.69 1.5" 50 5000 2400 0.56 1.79 4600 2400 0.55 1.76 4600 2400 1.32 4.22 68 5000 2400 0.49 1.57 4600 2300 0.48 1.54 4600 2300 1.15 3.69 3" 46 5000 2400 0.69 2.21 4800 2500 0.68 2.18 4800 2500 1.63 5.22 R6.0 1 70 4500 2600 0.81 2.59 4000 2100 0.8 2.56 4000 2100 1.92 6.14 100 4000 2200 0.61 1.95 3500 1800 0.6 1.92 3500 1800 1.44 4.61 1.5" 80 5000 2300 0.71 2.27 4000 2000 0.7 2.24 4000 2000 1.68 5.38 3" 69 5000 2700 0.81 2.59 4000 2200 0.8 2.56 4000 2200 1.92 6.14 ae Note 1) If the depth of cut is shallow, the revolution and feed rate can be increased, Note 2) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. a z LlI Q J259 ROUGHING BARREL TAPER RADIUS HQa SQUARE