1896 Каталог WALTER 2012 Металлорежущий инструмент и оснастка Valenite для станков Стр.E294

Каталог WALTER 2012 Инструмент и оснастка Valenite Стр. E294 1896 ENG Lab2u

WALTER Technical information Milling Prototyp Cutting data for shoulder / slot milling Cutting tool material HSS Family Des. Page NRA Kordel P312001 35° E 201 G 35 P3120017 35° E201 Vc in ft/min Feed matrices VT begin on page E 310 Material group Classification of the main material groups and code letters Brinell hardness HB Tensile strength Rm N/mm2 Machining group 1 6 40mm Z 4 + 6 uncoated + ACN Workpiece material 1/1 1/10 VT p Unalloyed steel C > 0.25 % annealed 125 428 P1 165 195 295 A C > 0.25 < 0.55 % annealed 190 639 P2 165 195 295 A C > 0.25 < 0.55 % tempered 210 708 P3 65 100 130 A C > 0.55 % annealed 190 639 P4 65 100 130 A C > 0.55 % tempered 300 1,013 P5 65 65 100 A Free cutting steel (short-chipping) annealed 220 745 P6 65 100 130 A Low-alloyed steel annealed 175 591 P7 65 100 130 A tempered 300 1,013 P8 65 65 100 A tempered 380 1,282 P9 tempered 430 1,477 P10 High-alloyed steel and high-alloyed tool steel annealed 200 675 P11 65 100 130 A hardened and tempered 300 1,013 P12 65 65 100 A hardened and tempered 400 1,361 P13 Stainless steel ferritic / martensitic, annealed 200 675 P14 35 35 65 A martensitic, tempered 330 1,114 P15 35 35 35 A M Stainless steel austenitic, quench hardened 200 675 M1 65 65 100 B austenitic, precipitation hardened (PH) 300 1,013 M2 35 35 35 B austenitic/ferritic, duplex 230 778 M3 35 35 65 B K Malleable cast iron ferritic 200 675 K1 65 100 130 A pearlitic 260 867 K2 65 65 100 A Grey cast iron low tensile strength 180 602 K3 65 100 165 A high tensile strength / austenitic 245 825 K4 65 100 130 A Cast iron with spheroidal graphite ferritic 155 518 K5 65 100 130 A pearlitic 265 885 K6 65 65 100 A Cast iron with vermicular graphite 200 675 K7 65 65 100 A N Aluminum wrought alloys cannot be hardened 30 N1 360 460 590 C hardenable, hardened 100 343 N2 360 460 590 C Cast aluminum alloys < 12 % Si, not hardenable 75 260 N3 195 260 360 C < 12 % Si, hardenable, hardened 90 314 N4 195 260 360 C > 12 % Si, not hardenable 130 447 N5 100 130 195 C Magnesium alloys 70 250 N6 195 260 360 C Copper and copper alloys (bronze / brass) unalloyed, electrolytic copper 100 343 N7 230 295 425 C Brass, bronze, red brass 90 4 31 N8 230 295 425 C Cu-alloys, short-chipping 110 382 N9 230 295 425 C high-strength, Ampco 300 1,013 N10 35 65 65 C S Heat-resistant alloys Fe-based annealed 200 675 S1 hardened 280 943 S2 Ni or Co base annealed 250 839 S3 hardened 350 1,177 S4 cast 320 1,076 S5 Titanium alloys Pure titanium 200 675 S6 a and p alloys, hardened 375 1,262 S7 P alloys 410 1,396 S8 Tungsten alloys 300 1,013 S9 Molybdenum alloys 300 1,013 S10 H Hardened steel hardened and tempered 50 HRC H1 hardened and tempered 55 HRC H2 hardened and tempered 60 HRC H3 Hardened cast iron hardened and tempered 55 HRC H4 O Thermoplasts without abrasive fillers O1 Thermosetting plastics without abrasive fillers O2 Plastic, glass-fiber reinforced GFRP O3 Plastic, carbon-fiber reinforced CFRP O4 Plastic, aramid fiber reinforced AFRP O5 Graphite (technical) 80 Shore O6 1 The machining groups are assigned from page H 8. E 294