Drilling with X offset Xtra-tec Insert Drill B 421x Drilling with X offset Drill stationary Workpiece rotating D Dc + 2 X Range 1 Range 2 Dc Inse

Drilling with X offset Xtra-tec Insert Drill B 421x Drilling with X offset Drill stationary Workpiece rotating D Dc + 2 X Range 1 Range 2 Dc Insert size mm Delta x Dmax mm Delta xmax Dmax mm 13.5 0.5 14.5 0.7 14.9 14 0.35 14.7 0.6 15.2 14.5 0.3 15.1 0.5 15.5 1 15 0.2 15.4 0.45 15.9 15.5 0.15 15.8 0.35 16.2 16 0.05 16.1 0.3 16.6 16.4 0 0.2 16.8 16.5 0.6 17.7 0.9 18.3 17 0.5 18 0.75 18.5 17.5 0.35 18.2 0.6 18.7 18 0.3 18.6 0.55 19.1 .5 8. 2 0.2 18.9 0.45 19.4 19 0.15 19.3 0.4 19.8 19.5 0.07 19.64 0.3 20.1 20 0 20 0.25 20.5 20.4 0 0.15 20.7 20.5 0.35 21.2 0.7 21.9 21 0.3 21.6 0.6 22.2 21.5 0.17 21.84 0.45 22.4 22 0.15 22.3 0.45 22.9 3 22.5 0.02 22.54 0.3 23.1 23 0 0.3 23.6 23.5 0 0.18 23.86 24 0 0.15 24.3 24.4 0 0 24.5 0.5 25.5 0.85 26.2 25 0.35 25.7 0.75 26.5 25.5 0.25 26 0.6 26.7 26 0.15 26.3 0.55 27.1 26.5 0.05 26.6 0.4 27.3 4 0 0.4 27.8 27.5 0 0.25 28 28 0 0.25 28.5 28.5 0 0.12 28.74 29 0 0.1 29.2 29.4 0 0 29.5 0.7 30.9 1.1 31.7 30 0.6 31.2 1 32 31 0.45 31.9 0.8 32.6 5 32 0.3 32.6 0.7 33.4 5 33 0.15 33.3 0.5 34 34 0 0.4 34.8 35 0 0.3 35.6 35.4 0 0.2 35.8 Range 1 Range 2 Dc Insert size mm Delta x Dmax mm Delta xmax Dmax mm 35.5 0.8 37.1 1.4 38.3 36 0.7 37.4 1.25 38.5 37 0.55 38.1 1.1 39.2 38 0.4 38.8 0.95 39.9 9 3 6 0.25 39.5 0.8 40.6 40 0.1 40.2 0.65 41.3 41 0 0.55 42.1 42 0 0.4 42.8 42.4 0 0.3 43 42.5 0.95 44.4 1.65 45.8 43 0.85 44.7 1.5 46 44 0.7 45.4 1.35 46.7 45 0.55 46.1 1.2 47.4 7 46 0.4 46.8 1.1 48.2 47 0.25 47.5 0.95 48.9 48 0.15 48.3 0.8 49.6 49 0 0.65 50.3 50 0 0.55 51.1 50.4 0 0.45 51.3 50.5 1.05 52.6 1.85 54.2 51 0.95 52.9 1.75 54.5 52 0.8 53.6 1.6 55.2 53 0.65 54.3 1.45 55.9 54 0.55 55.1 1.35 56.7 8 55 0.4 55.8 1.2 57.4 56 0.3 56.6 1.1 58.2 57 0.15 57.3 0.95 58.9 58 0 0.8 59.6 59 0 0.7 60.4 59.4 0 0.6 60.6 Outer insert with wiper edge (P4840P ) can only be used 2x. C 206 WALTER Valenite Technical information Drilling