83 Каталог TUNGALOY 2007 Режущий инструмент Точение Фрезерование Сверление Стр.79

Каталог TUNGALOY 2007 Режущий инструмент Стр. 79 0083 ENG Lab2u

80 Trigon Negative (Basic Selection) C 79 80o Trigon (Basic Selection Chipbreaker with Hole) WN Negative Chipbreaker type Insert Cat. No. WNMA080404 WNMA080408 WNMA080412 WNMA080416 cera..H4s Insert Cat. No. WNGA080404 WNGA080408 WNGA080412 Insert Cat. No. WNMG080404-TS WNMG080408-TS WNMG080412-TS Insert Cat. No. WNMG080404-CF WNMG080408-CF WNMG080412-CF Insert Cat. No. WNMG080404-SS WNMG080408-SS WNMG080412-SS Insert Cat. No. WNMG060404-TM WNMG060408-TM WNMG060412-TM WNMG080404-TM WNMG080408-TM WNMG080412-TM WNMG080416-TM Insert Cat. No. WNMG080408-CM WNMG080412-CM WNMG 08 04 04 - Cf Cutting edge length (2 ) Thickness (T) Chipbreaker type Corner radius (R) Standard cutting conditions Cutting speed Vc (m/min) Stocked grades Coated a "co E K 5 0 0 9 T 5 1 9 T 5 2 0 9 T 5 3 0 9 T 0 2 0 6 T 0 3 6 T 0 3 3 H G 5 0 1 5 T 5 1 1 5 T 5 2 5 T 0 1 0 5 T 0 2 0 5 T 0 1 X A 0 2 1 H A 0 2 5 S N 0 3 5 S N 0 2 5 T5A 0 3 5 T G 0 1 H T 1 1 X L T5010 100-300-600 T5010 100-250-500 X T5020 100-150-300 ap f 0.05-3.0-5.0 mm 0.03-0.3-0.6 mm/rev H LX11 50-100-150 LX11 50-100-150 ap f 0.05-0.3-0.5 mm 0.05-0.08-0.1 mm/rev P M NS520 80-250-350 GT530 120-140-180 NS530 80-150-250 X T9025 100-180-250 ap f 0.3-1.0-1.5 mm 0.08-0.15-0.2 mm/rev K T5105 180-330-480 T5115 180-270-400 X T5115 180-200-240 ap f 0.5-1.0-2.0 mm 0.05-0.25-0.4 mm/rev M S T6020 150-200-250 AH110 10-50-70 T6020 150-180-220 AH110 10-30-60 X T6030 50-100-150 AH120 10-30-50 ap f 0.5-1.0-3.0 mm 0.08-0.15-0.2 mm/rev P S T9005 100-250-400 AH120 10-40-60 T9015 80-150-250 AH120 10-30-50 X T9025 50-100-150 AH120 10-30-50 ap f 1.0-3.0-5.0 mm 0.2-0.3-0.5 mm/rev K T5105 180-330-480 T5115 140-270-400 X T5125 120-210-300 ap f 1.0-2.0-4.0 mm 0.1-3.0-0.5 mm/rev Cermet C.Cerm. Un.Ce. Chipbreaker selection P. 27 32 K Grade selection P. 37 39 K Insert hole diameter P. 42 Reference guide TAC Inserts (Negative)