401 Каталог TUNGALOY 2007 Режущий инструмент Точение Фрезерование Сверление Стр.397

Каталог TUNGALOY 2007 Режущий инструмент Стр. 397 0401 ENG Lab2u

SEE4000FP Shoulder milling and Slotting Work materials Carbon steels Cast irons Alloy steels Prehardened steels Stainless steels (e.g. X5CrNi18-10) Hardness 30HRC 40HRC - Vc (m/min) 50 - 80 35 - 65 20 - 45 Shoulder milling ap 1.0D ae 0.01D Slotting ap 0.2D Conditions No. of revolutions n (rpm) Feed rate Vf (mm/min) No. of revolutions n (rpm) Feed rate Vf (mm/min) No. of revolutions n (rpm) Feed rate Vf (mm/min) 0 4.0 5500 440 4300 280 2700 160 0 5.0 4400 350 3500 2200 0 6.0 3700 440 2900 350 1800 140 0 7.0 3100 2500 1500 150 0 8.0 2700 2100 1300 160 0 9.0 2400 1900 1200 0 10.0 2200 400 1700 310 1100 150 0 11.0 2000 1500 1000 160 0 12.0 1800 370 1400 290 920 0 13.0 1700 340 1300 260 850 150 0 14.0 1500 310 1200 250 790 140 0 15.0 1400 290 1100 230 740 130 0 16.0 1300 300 1000 210 690 0 17.0 280 200 650 0 18.0 1200 270 970 190 610 120 0 19.0 1100 280 920 180 580 110 0 20.0 260 870 170 550 Note SEE4000F SEE4000FP Down cut is generally recommended. For easy chip flow air-cooling rev. minimal quantity lubrication is recommended. When machining stainless steels and heat resistant alloys coolant (water soluble or water insoluble) should be used. Tool overhang should be as small as possible. Number of revolutions and feed rate should be reduced to minimise vibrations. SEE2000NA SEE4000NA Aluminium and nonferrous metals 47 helix angle 2 and 4 flute Extreme sharp cutting edge Shoulder milling and slotting 0D (mm) Tolerance (mm) 01.0 - 02.0 0 -0.030 03.0 - 06.0 -0.010 -0.040 07.0 - 010.0 -0.010 -0.045 011.0 - 016.0 -0.010 -0.050 Fig. 1 Fig. 2 Fig. 3 Fig. 4 ED SEE200QNA Standard stock in Europe Standard stock in Japan Cat. No. Stock No. of Dimensions (mm) Fig. Cat. No. Stock No. of Dimensions (mm) Fig. teeth 0D l1 L 0d teeth 0D l1 L 0d SEE2010NA 1.0 3.0 40 4.0 SEE2090NA 9.0 19.0 70 10.0 1 SEE2020NA 2.0 6.0 SEE2100NA 10.0 22.0 2 SEE2030NA 3.0 8.0 45 1 SEE2110NA 11.0 75 12.0 1 SEE2040NA 2 4.0 11.0 6.0 SEE2120NA 2 12.0 2 SEE2050NA 5.0 13.0 50 SEE2130NA 13.0 26.0 SEE2060NA 6.0 2 SEE2140NA 14.0 90 16.0 1 SEE2070NA 7.0 16.0 60 8.0 1 SEE2150NA 15.0 30.0 SEE2080NA 8.0 19.0 2 SEE2160NA 16.0 32.0 2 SEE4000NA Cat. No. Stock No. of teeth Dimensions (mm) Fig. Cat. No. Stock No. of teeth Dimensions (mm) Fig. 0D l1 L 0d 0D l1 L 0d SEE4030NA 3.0 10.0 45 6.0 3 SEE4100NA 10.0 26.0 70 10.0 4 SEE4040NA 4.0 13.0 SEE4110NA 11.0 75 12.0 3 SEE4050NA 5.0 15.0 50 SEE4120NA 12.0 28.0 4 SEE4060NA 4 6.0 16.0 4 SEE4130NA 4 13.0 SEE4070NA 7.0 20.0 RCl p n 3 SEE4140NA 14.0 on n an 1 r n 3 SEE4080NA 8.0 21.0 60 8.0 4 SEE4150NA 15.0 32.0 90 16.0 SEE4090NA 9.0 24.0 70 10.0 3 SEE4160NA 16.0 4 L Solid Carbide Endmills