317 Каталог TUNGALOY 2007 Режущий инструмент Точение Фрезерование Сверление Стр.313

Каталог TUNGALOY 2007 Режущий инструмент Стр. 313 0317 ENG Lab2u

For Face Milling Inserts (Used for TME4400I TME4400B) Corner details SEE CN SEE CN SEKR1203AGSR-MJ Fig- 1 Fig. 3 Fig. 4 A-A section Fig. 5 Right hand (R) shown Grades Cat. No. Accuracy Honing CVD Coated PVD Coated Cermet C. C. Uncoated Figure T3030 T1015 AH120 AH140 AH330 GH330 NS740 NS530 NS540 GT540 TH10 UX30 SECN1203AGFN C Without 2 SEEN1203AGTN SEEN1203AGFN E With Without A 2 SEEN1203AGTNCR With 3 SEKN1203AGTN SEKN1203AGFN SEKN1203AGTNCR K With Without With A 1 SEKN1203AGTN-T SEKN1203AGFN-T K With Without A 4 SEKR1203AGSR-MJ K With 5 SEMR1203AFTN-MJ M With A - Note SEDN1230AGDN(conventional type) and SEDN1203AGDN1203AGN-T(strengthened type) inserts should not be used together with each other in the same cutter body. SEnN1230(42)AFDN type inserts should not be used in the TME4400 type body. SECN1230AGFN type is exclusively used for milling aluminium alloys and other non-ferrous light alloys. Its top flat face is ground to mirror-like finish. The strengthened type inserts have greater edge strength to prevent edge chipping. Parts Cat. No. No. Description TME4463R/LBE TME4403R/LI 4405R/LI TME4403R/LB 4405R/LB TME4406R/LI 4412R/LI TME4406R/LB 4412R/LB Locator LE444R/L LE444R/L LE446R/L Insert locking wedge WT402R/L WF444R/L WF444R/L Wedge fixing screw DS-8 FDS-8S FDS-8S Locator fixing screw M4 X 0.7 X 14 CM4 X 0.7 X 14 CM4 X 0.7 X 14 T-handle wrench TP-4 TP-4 TP-4 Standard cutting conditions Work materials Insert grades Roughing (Cutting depth 1.5 4 mm) Finishing (Cutting depth 0.3 0.7 mm) Vc (m/min) ft (mm t) Vc (m/min) ft (mm t) Mild steels ( 180 HB) St37 etc. NS540 NS740 150 250 0.10 0.20 150 250 0.10 0.25 GH330 AH120 150 200 0.10 0.25 150 250 0.10 0.28 T3030 150 280 0.10 0.28 180 300 0.10 0.30 AH330 150 300 0.10 0.25 150 350 0.10 0.25 UX30 AH140 100 180 0.10 0.28 130 200 0.10 0.30 Carbon steels Alloy steels ( 300 HB) Ck45 42CrMo4 etc. T3030 150 230 0.10 0.25 200 300 0.10 0.28 NS540 NS740 100 180 0.10 0.18 150 200 0.10 0.23 GH330 AH120 100 200 0.10 0.23 150 200 0.10 0.25 AH330 150 250 0.10 0.25 200 320 0.10 0.25 UX30 80 130 0.10 0.25 100 150 0.10 0.28 Stainless steels ( 250 HB) AH140 80 180 0.15 0.25 100 200 0.15 0.28 AH120 150 230 0.15 0.23 200 250 0.15 0.25 UX30 150 180 0.15 0.23 180 200 0.15 0.25 Die steels ( 30 HRC) X96CrMoV12 etc. AH120 GH330 100 150 0.10 0.15 100 150 0.10 0.20 AH330 100 200 0.10 0.15 100 250 0.10 0.20 UX30 80 130 0.10 0.15 80 130 0.10 0.20 Cast irons Ductile cast irons T1015 100 200 0.10 0.20 100 200 0.10 0.25 TH10 UX30 80 130 0.10 0.20 80 130 0.10 0.25 Aluminium alloys (Si 12%) TH10 200 1000 0.10 0.20 350 1000 0.10 0.30 Copper alloys TH10 200 500 0.10 0.20 200 500 0.10 0.25 Note Dry cutting is recommended for all materials except for aluminium alloys. No. of revolutions n (rpm) Cutting speed Vc (m/min) x 1000 3.14 Cutter 0 (mm) Table feed Vf (mm/min) n (rpm) x Feed per tooth ft (mm t) x t (No. of inserts) Features Reference Technical data P. 298 302 guide P. 476 479 TAC Mills