1325 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.M169

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. M169 1325 Lab2u

MAXIMUM CAPACITIES BY MODE RAMPING HELICAL DRILLING How to derive a locus of the centre of the tool. 0dc = 0DH - DCX Locus of Desired hole Cutting Diameter the center of diameter Maximum the tool For the depth of cut per pass, refer to the cutting conditions above for helical drilling. Set the machine spindle revolution so that the tool is rotating and cutting in a down cut direction. When ramping and helical cutting, please apply a lower feed (60% of the calculated feed rate or less). When drilling, please set the feed in the axial direction at 0.2mm/rev or less. 9 The long chips generated can disperse, ensure that adequate safety precautions are taken. APMX Ramping Helical Drilling Tool Holder Type DCX DC RMPX L Required distance for X mm depth DH AZ FT/JM/ST Breaker JL Breaker X=1 X=1.2 X=1.5 X=2 Min Max AJX06 16 8.9 1 0.6 3° 19.1 - - - 23 29 0.3 AJX06 17 9.9 1 0.6 2.5° 22.9 - - - 25 31 0.3 AJX06 20 12.9 1 0.6 1.5° 38.2 - - - 31 37 0.3 AJX06 22 14.9 1 0.6 1° 57.3 - - - 35 41 0.3 AJX08 20 11.4 1.5 0.9 3.5° 16.3 19.6 24.5 - 27 36 0.5 AJX08 22 13.4 1.5 0.9 3° 19.1 22.9 28.6 - 31 40 0.5 a> AJX08 25 16.4 1.5 0.9 2° 28.6 34.4 43 - 37 46 0.5 AJX08 28 19.4 1.5 0.9 1.7° 33.7 40.4 50.5 - 43 52 0.5 AJX09 25 14.9 2 1.2 4° 14.3 17.2 21.5 28.6 33 46 1 D i u AJX09 28 17.9 2 1.2 3° 19.1 22.9 28.6 38.1 39 52 1 (/) a5 AJX09 30 20 2 1.2 2.7° 21.2 25.4 31.8 42.4 43 56 1 AJX09 32 21.9 2 1.2 2.5° 22.9 27.5 34.4 45.8 47 60 1 c ro AJX09 35 24.9 2 1.2 2° 28.6 34.4 43 57.3 53 66 1 /) AJX09 40 29.9 2 1.2 1.5° 38.2 45.8 57.3 76.4 63 76 1 AJX12 30 18.3 2 1.2 4.5° 12.7 15.2 19 25.4 39 56 1.5 AJX12 32 20.3 2 1.2 4° 14.3 17.2 21.4 28.6 41 60 1.5 AJX12 35 23.3 2 1.2 3.5° 16.3 19.6 24.5 32.7 47 66 1.5 AJX12 40 28.3 2 1.2 3° 19.1 22.9 28.6 38.2 57 76 1.5 AJX14 50 38.2 2 1.2 4.2° 13.6 16.3 20.4 27.2 72 96 2 AJX14 63 51.1 2 1.2 2.8° 20.4 24.5 30.7 40.9 98 122 2 AJX09 50 40 2 1.2 1.1° 52.1 62.5 78.1 104.2 83 96 1 AJX12 50 38.3 2 1.2 2° 28.6 34.4 43 57.3 77 96 1.5 AJX12 63 51.3 2 1.2 1.5° 38.2 45.8 57.3 76.4 103 122 1.5 i> AJX12 80 68.3 2 1.2 1.1° 52.1 62.5 78.1 104.2 137 156 1.5 a. AJX12 100 88.3 2 1.2 0.8° 71.6 85.9 107.4 143.2 177 196 1.5 o n AJX14 63 51.1 2 1.2 2.8° 20.4 24.5 30.7 40.9 98 122 2 AJX14 80 68.1 2 1.2 1.8° 31.8 38.2 47.7 63.6 132 156 2 AJX14 100 88.1 2 1.2 1.2° 47.7 57.3 71.6 95.5 172 196 2 AJX14 125 113.2 2 1.2 O 00 71.6 85.9 107.4 143.2 222 246 2 AJX14 160 148.2 2 1.2 O CJI 114.6 137.5 171.9 229.2 292 316 2 M M169 INDEXABLE MILLING