1063 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.K031

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. K031 1063 Lab2u

CARBIDE RECOMMENDED CUTTING CONDITIONS Shoulder milling (L/D=3) Other than the L/D = 3, use following recommended cutting conditions by multiplying the K003 page correction factor by overhang length. (mm) Work Material Carbon steel, Alloy steel, Mild steel, Pre-hardened steel AIS11045, AISI 4140, AISI 4340, ASTM A36, AIS11010, AISI P21, AISI P20 Austenitic stainless steel, Ferritic and Martensitic stainless steels, Cobalt chromium alloy, Titanium alloy AISI 304, AISI 316, AISI 431, AISI 420J2, AISI 630, AISI 631, Ti-6AI-4V Inclination angle a<15" a>15” Depth of Cut ap Width of Cut ae Ct<15” a>15° Depth of Cut ap Width of Cut ae Dia DC Radius of Bell Nose RE Cuttng Speed (m/min) Revolution (min-1) FeedperTMth (mm/t.) Feed rate (mm/min) Cutting Speed (m/min) Revolution (min-1) Feed perTooth (mm/t.) Feed rate (mm/min) Cutting Speed (m/min) Revolution (min-1) Feed perTooth (mm/t.) Feed rate (mm/min) Cutting Speed (m/min) Revolution (min-1) Feed pa Toolli (mm/t.) Feed rate (mm/min) 10 5 300 9500 0.106 6000 200 6400 0.07 2700 0.5 2 225 7200 0.105 4500 150 4800 0.067 1900 0.5 2 12 6 300 8000 0.125 6000 200 5300 0.085 2700 0.6 2.4 225 6000 0.125 4500 150 4000 0.08 1900 0.6 2.4 16 8 300 6000 0.134 4800 200 4000 0.088 2100 0.8 3.2 225 4500 0.14 3800 150 3000 0.09 1600 0.8 3.2 20 10 300 4800 0.156 4500 200 3200 0.1 1900 1 4 225 3600 0.16 3500 150 2400 0.105 1500 1 4 25 12.5 300 3800 0.16 3600 200 2500 0.1 1500 1.2 5 225 2900 0.16 2800 150 1900 0.105 1200 1.2 5 CC LlI a. I o 0 z 1 o 3 o DC Depth of cut Work Material Heat resistant alloys lnconel718 Inclin an ation a<15’ £ >15” Depth of Cut ap Width of Cut ae Dia DC Radius of Bill Nose RE Cuttng Speed (m/min) Revolution (min-1) Feel r Toot (mm/t.) Feed rate (mm/min) Cutting Speed (m/min) Revolution (min-1) Feed perTooth (mm/t.) Feed rate (mm/min) 10 5 60 1900 0.055 630 40 1300 0.035 270 0.5 1 12 6 60 1600 0.055 530 40 1100 0.035 230 0.6 1.2 16 8 60 1200 0.062 450 40 800 0.04 190 0.8 1.6 20 10 60 950 0.062 350 40 640 0.04 150 1 2 25 12.5 60 760 0.062 280 40 510 0.04 120 1.2 2.5 Depth of cut Note 1) For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. Note 2) If the depth of cut is shallow, the revolution and feed rate can be increased. Note 3) The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. Note 4) a is the inclination angle of the machined surface. a m K031