982 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J360

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J360 0982 Lab2u

SOLID END MILLS NEW VQT6UR Barrel, Medium cut length, 6 flute LU D o /> m /> D O O' RECOMMENDED CUTTING CONDITIONS Effective Angle Please refer to the table below for the use of the nose radius (RE1) and tangential form radius (RE2). (mm) Order Number Nose Radius Tangential Form Radius RE1 Effective Angle RE2 Effective Angle VQT 6URR020R075S08 2 76.6° 75 13.4° VQT 6URR020R085S10 2 74.5° 85 15.5° VQT 6URR030R075S10 3 76.4° 75 13.6° VQT 6URR040R100S12 4 78.3° 100 11.7° RE2 LU Q. I Side Milling with the Use of the Tangential Form Radius (RE2) Work Material Mild Steels (<180HB) Carbon Steels, Cast Irons (180 -280HB) Austenitic Stainless Steels (<200HB) Titanium Alloys Aluminum Alloys (Si 5%) DC RE2 Revolution Feed rate Depth ofcut Revolution Feed rate Depth ofcut Revolution Feed rate Depth ofcut (mm) (mm) (min-1) (mm/min) ap (mm) (min'1) (mm/min) ap (mm) (min'1) (mm/min) ap (mm) 8 75 8000 2400 0.05-0.3 3200 770 0.05-0.3 16000 4800 0.05-0.3 10 85 6400 1900 0.05-0.3 2500 600 0.05-0.3 13000 3900 0.05-0.3 10 75 6400 1900 0.05-0.3 2500 600 0.05-0.3 13000 3900 0.05-0.3 12 100 5300 1600 0.05-0.3 2100 500 0.05-0.3 11000 3300 0.05-0.3 I Depth ofCut Calculation Table Based on Tangential Form Radius (RE2) and Cusp Height (h) (mm) Work Material RE2 Cusp Height h 0.0001 0.0003 0.0005 0.0008 0.001 0.003 0.005 0.008 VQT 6U RR020R075S08 75 0.245 0.424 0.548 0.693 0.775 1.342 1.732 2.191 VQT 6URR030R075S10 75 Depth of Cut ap 0.245 0.424 0.548 0.693 0.775 1.342 1.732 2.191 VQT6U RR020R085S10 85 0.261 0.452 0.583 0.738 0.825 1.428 1.844 2.332 VQT6URR040R100S12 100 0.283 0.49 0.632 0.8 0.894 1.549 2 2.53 UJ Q O in Note 1) SMART MIRACLE coating has very low electrical conductivity; therefore, an external contact type of tool setter (electric transmitted) may not work. When measuring the tool length, please use an internal contact type (non-electricity type) or a laser tool setter. Note 2) It is recommended to use this tool only for finish cutting. Note 3) The tool contact part differs between the nose radius and tangential form radius depending on machining geometries and tilt angles. Select suitable cutting conditions according to tool contact parts. J360