925 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J303

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J303 0925 Lab2u

CARBIDE RECOMMENDED CUTTING CONDITIONS Side milling Work Material Carbon steel, Alloy steel, Mild steel AISI 1045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Hardened stainless steels, Cobaly chromium alloy AISI 630, AISI 631, 15-5PH, 17-4PH Copper, Copper alloy Heat resistant alloys lnconel718 Dia. DC (mm) M Revolution (min-1 Feed rate (mmlmin) DqMoit ap (mm) Depthtfcut ae (mm) Citing tpl (m, Revolution (min-1) Feed rate (mmlmin Depthcfcut ap (mm) Depth olrat ae (mm) Cuttra speeJ intahl Revolution (min-1) Feed rate (mm/min Depth of cut ap (mm) Dqiiolcut ae (mm) Mpeti iiinkin) Revdulion (mirr1) Feed rate (mmlmin) Defithofcut ap (mm) Depthrfcut ae (mm) (Mnjsped (nm/rin) It Feed rate (mmlmin) Dejtiofcut ap (mm) Deptitfcut ae(mm) 6 150 8000 2600 9 0.3 120 6400 1300 9 0.3 75 4000 800 9 0.3 180 9500 3000 9 0.3 40 2100 250 9 0.18 8 150 6000 2500 12 0.4 120 4800 1300 12 0.4 75 3000 840 12 0.4 180 7200 3000 12 0.4 40 1600 260 12 0.24 10 150 4800 2300 15 0.5 120 3800 1200 15 0.5 75 2400 770 15 0.5 180 5700 2700 15 0.5 41 1300 290 15 0.3 12 150 4000 1900 18 0.6 120 3200 1200 18 0.6 75 2000 720 18 0.6 180 4800 2300 18 0.6 41 1100 280 18 0.36 16 150 3000 1600 24 0.8 120 2400 960 24 0.8 75 1500 600 24 0.8 180 3600 1900 24 0.8 40 800 200 24 0.48 I Bottom face milling Work Material Carbon steel, Alloy steel, Mild steel AISI 1045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Hardened stainless steels, Cobaly chromium alloy AISI 630, AISI 631, 15-5PH, 17-4PH Copper, Copper alloy Heat resistant alloys lnconel718 Dia. DC (mm) M Revolution (min-1) Feed rate (mmlmin) Deptiiofnit ap (mm) Depthofcut ae (mm) Cutliigspnl (mnir) Revolution (min-1) Feed rate (mmlmin) Depthcfcut ap (mm) Depth of cut ae (mm) OlriSjKii iaMi) Revolution (min-1) Feed rate (mm/min) Depth of cut ap (mm) Deptiofcut ae (mm) Mng speed mMi Revdulion (mirr1) Feed rate (mmlmin) Depthofcut ap (mm) Depthrfcut ae (mm) Mngspeed fiiim) fa 11 Feed rate (mmlmin) Dojtiofcut ap (mm) Deptnfcut ae(mm) 6 110 5800 1400 0.3 4.8 90 4800 770 0.3 4.8 55 2900 460 0.3 4.8 130 6900 1700 0.3 4.8 30 1600 180 0.18 4.8 8 110 4400 1200 0.4 6.4 90 3600 720 0.4 6.4 55 2200 440 0.4 6.4 130 5200 1500 0.4 6.4 30 1200 190 0.24 6.4 10 110 3500 1100 0.5 8 90 2900 640 0.5 8 55 1800 400 0.5 8 130 4100 1300 0.5 8 30 950 210 0.3 8 12 110 2900 930 0.6 9.6 90 2400 580 0.6 9.6 55 1500 360 0.6 9.6 130 3400 1100 0.6 9.6 30 800 200 0.36 9.6 16 110 2200 790 0.8 12.8 90 1800 500 0.8 12.8 55 1100 310 0.8 12.8 130 2600 940 0.8 12.8 30 600 150 0.48 12.8 Depth of cut Note 1) SMART MIRACLE Coating is not energized because of its nature. Therefore, an external contact (voltaic type) tool setter cannot be used. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. Note 2) Effective cutting of stainless steel, titanium alloys and heat-resistant alloys etc. can be achieved with the use of emulsion. Note 3) Chattering can still occur if the machine rigidity and clamping method are insufficient. In these cases the feed and speed should be reduced proportionately. Note 4) When the depth of cut is smaller than shown the feed rate can be increased. a z LlI a J303 ROUGHING BARREL TAPER rlilrillfcM BALL SQUARE