885 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.J263

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. J263 0885 Lab2u

CARBIDE RECOMMENDED CUTTING CONDITIONS Work Material Carbon steel, Cast iron, Alloy steel (-30HRC) AISI 1050, AISI No 35 B, AISI P20 Alloy steel, Tool steel, Pre-hardened steel AISI H13, AISI W1-10, AISI P21 Hardened steel (45 55HRC) AISI H13 Hardened steel (55-62HRC) AISI D2 R RE (mm) Taper angle one side BHTA2 Neck length LB2 (mm) Revolution (min'1) Feed rate (mm/min) Depth of cut ap (mm) Revolution (min'1) Feed rate (mm/min) Depth of cut ap (mm) Revolution (min'1) Feed rate (mm/min) Depth of cut ap (mm) Revolution (min'1) Feed rate (mm/min) Depth of cut ap (mm) R0.4 0.4" 6 34000 2700 0.03 31000 2200 0.025 24000 1700 0.02 19000 1400 0.015 8 31000 2100 0.02 29000 1700 0.02 22000 1300 0.015 18000 1000 0.01 12 28000 2000 0.015 26000 1600 0.01 20000 1200 0.01 16000 960 0.007 0.9’ 8 31000 2200 0.02 29000 1800 0.02 22000 1400 0.015 18000 1100 0.01 12 28000 2100 0.015 26000 1700 0.01 20000 1300 0.01 16000 1000 0.007 16 25000 1100 0.01 23000 910 0.01 18000 700 0.008 14000 560 0.006 RO.5 0.4' 8 27000 2700 0.04 25000 2200 0.04 19000 1700 0.03 15000 1400 0.02 10 24000 2200 0.03 22000 1800 0.025 17000 1400 0.02 14000 1100 0.015 12 24000 2200 0.03 22000 1800 0.025 17000 1400 0.02 14000 1100 0.015 16 22000 2100 0.03 21000 1700 0.025 16000 1300 0.02 13000 1000 0.015 20 20000 1400 0.015 18000 1200 0.01 14000 900 0.01 11000 720 0.007 25 18000 1300 0.015 17000 1000 0.01 13000 800 0.009 10000 640 0.006 30 15000 960 0.01 14000 780 0.01 11000 600 0.008 8800 480 0.006 35 14000 800 0.008 13000 650 0.007 10000 500 0.006 8000 400 0.004 0.9" 8 27000 2900 0.04 25000 2300 0.04 19000 1800 0.03 15000 1400 0.02 12 24000 2400 0.03 22000 2000 0.025 17000 1500 0.02 14000 1200 0.015 16 22000 2200 0.03 21000 1800 0.025 16000 1400 0.02 13000 1100 0.015 20 20000 1600 0.015 18000 1300 0.01 14000 1000 0.01 11000 800 0.007 25 18000 1400 0.015 17000 1200 0.01 13000 900 0.009 10000 720 0.006 30 15000 1100 0.01 14000 910 0.009 11000 700 0.008 8800 560 0.006 35 14000 960 0.008 13000 780 0.007 10000 600 0.006 8000 480 0.004 40 11000 800 0.007 11000 650 0.006 8000 500 0.005 6400 400 0.003 50 8400 610 0.006 7800 490 0.005 6000 380 0.004 4800 300 0.003 60 7000 510 0.004 6500 400 0.004 5000 320 0.003 4000 260 0.002 70 7000 480 0.003 6500 390 0.002 5000 300 0.002 4000 240 0.001 1.5" 12 24000 2600 0.03 22000 2100 0.025 17000 1600 0.02 14000 1300 0.015 16 22000 2400 0.03 21000 2000 0.025 16000 1500 0.02 13000 1200 0.015 20 20000 1800 0.015 18000 1400 0.01 14000 1100 0.01 11000 880 0.007 25 18000 1600 0.015 17000 1300 0.01 13000 1000 0.009 11000 800 0.006 30 15000 1300 0.01 14000 1000 0.01 11000 800 0.008 8800 640 0.006 35 14000 1100 0.008 13000 910 0.007 10000 700 0.006 8000 560 0.004 o in Depth of cut 30.1 RE (RE31) 0.2RE (RE>1) RE: Radius / Note 1) If the depth of cut is shallow, the revolution and feed rate can be increased. Note 2) If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. J263 ROUGHING BARREL TAPER RADIUS HQa SQUARE