245 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.B015

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. B015 0245 Lab2u

CBN Suitable for high speed finishing of heat treated steel, sintered ferrous alloy and cast iron. Low affinity to iron, thus good surface finishes are possible. Grinding can be replaced by machining. B Heat Treated Steel Work Material Type Cutting Mode Recommended Grade Recommended Cutting Conditions Cutting Speed vc (m/min) Feed f (mm/rev) Depth of Cut ap (mm) Cutting Mode Structural Steel Esp. Carburized Steel (SC, SCM, SCr) High Alloy Steel (SKD, SKH) 35-65 HRC Coated High speed finishing cutting BC8105 250 (100-350) £0.15 £0.2 Dry,Wet Continuous cutting for general purpose BC8110 200 (100-300) £0.2 £0.35 Dry, Wet BC8120 200 (100-230) 0.3 £0.8 Dry,Wet Medium interrupted cutting BC8120 150 (60-200) 0.2 0.3 Dry,Wet Interrupted cutting BC8130 120(60-150) £0.2 £0.3 Dry,Wet Non-coated Continuous cutting for general purpose new MB8110 200 (100-250) £0.2 £0.3 Dry,Wet new MB8120 150 (80-220) 0.2 £0.5 Dry,Wet Medium Interrupted cutting new MB8120 130(85-180) £0.2 £0.3 Dry,Wet Interrupted cutting new MB8130 100(60-150) £0.2 £0.3 Dry,Wet Cast Iron Work Material Workpiece Structure Cutting Speed vc (m/min) Feed f(mmA'ev) Depth of Cut ap (mm) Cutting Mode 250 500 750 1000 1250 Gray Cast iron JISFC250 Ferritic + Pearlitic MBS140 -0.5 -1.0 MBS140 -5.0 Dry, Wet JISFC300 Pearlltlc MB710 1 MB730 1 Alloy Cast Iron Pearlitic MB710 MB4120 new -0.4 -0.5 Dry.Wet Ductile Cast Iron JISFCD400 Ferritic I MB710 -0.4 -0.5 Dry.Wet JISFCD700 Ferritic + Pearlltlc Pearlitic MB730 Sintered Alloy Work Material Recommended Recommended Cutting Conditions Grade Cutting Speed vc (m/min) Feed f (mm/rev) Depth of Cut ap (mm) General Sintered Alloy w MB4120 180(80-300) -0.2 -0.3 High Density Sintered Alloy new MB4120 150(80-230) -0.2 -0.3 Sintered Alloy aw MB4120 130(80-180) -0.2 -0.3 Valve Seat Hardness of Workpiece (HV) 150 250 300 350 Plunge Cut w MB4120, MB4020) MB825 MB835 Traverse Cut (new MB4120, MB4020 E( MB710 M MB825 m Roll Work Material Grade Recommended Cutting Conditions Cutting Speed vc (m/hiln) Feed f (mm/rev) Depth of Cut ap (mm) Cast Steel Adamite Cast Steel MB8025 80 (30-130) 0.3 (0.1-0.5) 0.2 3.0 Ductile Cast Iron Granular Cast Iron Chilled Cast Iron MB710 80 (30-130) 0.3 (0.1-0.5) 0.2 3.0 High Chromium Steel High Alloy Steel MB8025 80 (30-130) 0.3 (0.1-0.5) 0.2 3.0 High Speed Steel MB730 50 (20-70) 0.25 (0.1 -0.4) 0.1-3.0 Cemented Carbide MB730, MBS140 20(10-30) -0.2 -0.2 Heat Resistant Al oy Work Material Grade Recommended Cutting Conditions Cutting Speed vc (m/min) Feed f (mm/rev) Depth of Cut ap (mm) Ni Base, Heat Resistant Alloy (e.g. Inconel) MB730, MB8025 120(100-150) -0.2 -0.5 Co Base Heat Resistant Alloy (e.g. Stellite) MB730, MB8025 70 (50-100) -0.2 -0.5 B015 CBN & PCD TURNING INSERTS