Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ 1/AMR Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Side milling Work material Structural steel, Cast iron, Carbon steel AIS11045, AISI No 35 B, AIS11050 Carbon steel, Alloy steel (20 30HRC) AIS11055, AISI P20 Alloy steel, Tool steel, Prehardened steel (30 35HRC) AISI H13, AISI D2 Austenitic stainless steel, Alloy steel, Tool steel (35 40HRC) AISI 304, AISI 316 Dil. Mutton FHd nte Mutton Feed nte Mutton FHd nte Mutn Feed nte DCH (miir1) (mm/min) (min-1) fnmjmin) (miir1) (mmMiin) (miir1) mnMn) 5 2400 120 1800 90 1200 60 1000 50 6 2200 155 1700 120 1100 70 930 65 8 1800 200 1400 140 950 100 780 85 10 1500 250 1100 200 810 125 680 100 12 1250 270 960 220 680 160 560 120 16 930 270 720 220 510 160 430 120 20 750 290 580 220 410 160 340 120 25 600 270 460 210 320 140 270 120 30 490 250 380 200 270 140 230 120 40 300 180 230 140 160 105 140 90 50 210 140 160 110 110 80 90 65 <0.5DC Slotting Work material Structural steel, Cast iron, Carbon steel AIS11045, AISI No 35 B, AIS11050 Carbon steel, Alloy steel (20 30HRC) AIS11055, AISI P20 Alloy steel, Tool steel, Pre-hardened steel (30 35HRC) AISI H13, AISI D2 Austenitic stainless steel, Alloy steel, Tool steel (35 40HRC) AISI 304, AISI 316 Dil. Mutton Feed nte Mutton Feed nte Revolution Feed nte Mutkn Feed nte Dtfynm) tniir1) (mm/min) jmin-1 (nmlmin) fir1) tynmlmin) (miir1) (mmtnin 5 1800 85 1350 60 920 40 740 25 6 1700 110 1300 85 830 45 700 35 8 1300 140 1050 100 730 70 600 50 10 1100 170 810 140 620 85 520 60 12 900 190 740 160 520 115 420 75 16 680 190 540 160 390 115 330 75 20 550 195 440 150 320 115 260 75 25 440 170 350 135 240 90 200 70 30 350 160 270 120 180 75 155 65 40 240 120 180 90 120 60 105 55 50 260 90 125 75 80 50 70 40 DC Supply cutting fluid sufficiently during cutting. When slotting with dry cut, decrease the revolution and feed rate proportionately by 20 50%. When the diameter exceeds 030 and the metal removal is less than the quantity shown in the table, the revolution and feed rate may be increased proportionately by 10 40%. If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. 1194 Mitsubishi Materials