Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ EgMS Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS (): Indicates standard feed rate for slotting. Work material Structural steel. Carbon steel AIS11045, AIS11050 Carbon steel, Alloy steel (20 30HRC) AIS11055, AISI P20 Alloy steel, Tool steel, Pre-hardened steel (30 35HRC) AISI P20, AISI H13 AISI D2 Austenitic stainless steel AISI 304, AISI 316 Cast iron AISI No 35 B Aluminium alloy Dil. Million Feed rite RngMiffl Feed rate Revdution Feed nte Revdution Feed nte Reiokition Feed nte Mifin Feed nte DCJnm (mir') (mn/min (miir1) (mn/min (miir' (mmlmin (miir' (mmJmin (min-' (mm/min ntirl mm/min 1 6400 80(65) 5000 50(40) 3600 35(30) 2900 25(20) 5400 85(70) 13000 170(135) 2 3700 85(70) 3100 60(50) 2200 50(40) 1700 30(25) 3200 90(70) 8200 190(150) 3 2800 90(70) 2200 65(50) 1700 55(45) 1300 35(30) 2400 95(75) 5800 240(190) 4 2150 100(80) 1700 70(55) 1300 55(45) 1000 35(30) 1900 110(90) 4600 310(250) 5 1900 115(90) 1450 90(70) 1100 60(50) 850 40(30) 1600 120(95) 3800 360(290) 6 1700 120(95) 1200 90(70) 940 65(50) 730 50(40) 1300 130(105) 3400 400(320) 8 1300 130(105) 960 95(75) 700 65(50) 560 50(40) 1000 140(110) 2600 460(370) 10 1000 145(115) 770 110(90) 560 65(50) 460 55(45) 840 160(130) 2200 430(350) 12 860 130(105) 640 95(75) 470 60(50) 370 50(40) 700 140(110) 1900 420(340) 16 650 115(90) 480 90(70) 360 55(45) 280 40(30) 530 120(95) 1450 350(280) 20 520 95(75) 380 70(55) 290 45(35) 230 35(30) 420 100(80) 1150 300(240) 25 420 85(70) 300 60(50) 230 40(30) 180 30(25) 340 90(70) 910 260(210) 30 350 80(65) 250 55(45) 190 35(30) 145 25(20) 290 85(70) 770 240(190) 40 250 60(50) 180 35(30) 140 25(20) 110 22(18) 220 65(50) 580 190(150) DC ’’L r 0.1 DC (DC <02) t 0.3DC (02 DC 03) .Wl L<0.5DC (DC >03) SB If the rigidity of the machine or the work materials installation is very low, or chattering and noise are generated, reduce the revolution and feed rate proportionately. 0.1 DC (DC 03) <0.2DC (DC >03) <1.5DC 1154 Mitsubishi Materials