Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ VnMHZVOH Work material Hardened stainless steels, Cobalt chromium alloy AISI 630, AISI 631 15-5PH.17-4PH Copper, Copper alloys Heat resistant alloys lnconel718 Daneter DC(mm Cutthg Speed (m/min RevoMoi (milt4 Feed rate (mmlmin Depth of cut CiMing Speed (mini) Revolutior (mir4 Feed nte (nun/irin) Depth of nit )p(mm Ming Speed tyninin Revdotion (miir' Feed nte (mmtnh Depth of cut ipfmm 6 50 2700 210 3 120 6400 760 6 25 1300 72 1.8 8 50 2000 200 4 120 4800 670 8 25 990 78 2.4 10 50 1600 170 5 120 3800 600 10 25 800 89 3 12 50 1300 150 6 120 3200 510 12 25 660 84 3.6 16 50 990 140 8 120 2400 430 12 25 500 63 4.8 DC tap 1 wi/i/mm SMART MIRACLE Coating is not energized because of its nature. Therefore, an external contact (voltaic type) tool setter cannot be used. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. An internal contact (non-voltaic) type or laser type tool setter is recommended to measure the length of the tool. For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abonrmal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. When the Depth of cut is small, the feed rate can be increased. Plunging The rigidity of the machine or workpiece and chip discharge are sufficient at high efficiency conditions. The rigidity of the machine or workpiece or chip discharge is insufficient at general-purpose conditions. High efficiency conditions Work material Carbon steel, Alloy steel, Mild steel AIS11045, AISI 4140,ASTM A36, AISI1010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20.AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steels, Titanium alloys stainless steels, Titanium alloys AISI 304, AISI 316, Ti-6AI-4V etc. DMer Cling Speed Revolution Feed nte Depth of Hole Step Cutting Spaed Revolution Feed nte Depth of Hole Step Cutting Speed Rewlutim Feed nte Depth of Hole Step DC mm (m(mh (miir1 (nrntjin ap(nm M (mhiin (miir'l (mmlminl ap mm lmlmin miit4 (mmlmin ip mm mm 6 100 5300 950 9 3 70 3700 440 9 1.2 60 3200 100 6 0.6 8 100 4000 720 12 4 70 2800 340 12 1.6 60 2400 70 8 0.6 10 100 3200 580 15 5 70 2200 260 15 2.5 60 1900 60 10 0.6 12 100 2700 490 18 5 70 1900 230 18 3 60 1600 50 12 0.6 16 100 2000 360 24 5 70 1400 170 24 4 60 1200 40 16 0.6 784 Mitsubishi Materials