Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ VF45VB Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Work material Alloy steel. Tool steel, Pre-hardened steel AISI H13, AISI W1-10, AISI P21 Austenitic stainless steel, Titanium alloy AISI 304, AISI 306, Ti-6AI-4V Heat resistant alloys lnconel718 R RE (mm 1 15' l>15' Depth of cut (mm Pick feed Pf mti g 1P Depth of cut ap fynm Pick feed Pf (mm o ir ooir Depth of cut ip (mil Pick feed i M Revolution (miir1 Fnd nit (mmlmin Revolution (nil4 Fied rate (mmimnl Revolution miir4 Feed rale (mnMn Revolution (miir1 Feed rale (mmMn Revolution (niir1 Feed rate (itnfmin Revolution milt4 Feed rate nnJmin R1 40000 8000 32000 3800 0.17 0.5 36000 6500 24000 2900 0.17 0.5 9600 960 6400 510 0.08 0.2 R1.5 32000 7700 21000 3200 0.25 0.75 24000 4800 16000 1900 0.25 0.75 6400 640 4200 340 0.13 0.3 R2 24000 5800 16000 2800 0.33 1 18000 4000 12000 1700 0.33 1 4800 580 3200 260 0.17 0.4 R2.5 19000 5300 12700 2600 0.42 1.25 14400 3500 9600 1500 0.42 1.25 3800 530 2500 250 0.21 0.5 R3 16000 4800 10600 2100 0.5 1.5 12000 3200 8000 1400 0.5 1.5 3200 500 2100 210 0.25 0.6 R4 12000 4300 8000 1900 0.8 S2 9000 3200 6000 1400 0.8 2400 430 1600 190 0.4 0.8 R5 9600 4100 6400 1800 1 2.5 7200 3000 4800 1300 1 2.5 2000 420 1300 180 0.5 1 R6 8000 4000 5300 1800 1.2 3 6000 3000 4000 1300 1.2 S=3 1700 350 1100 150 0.6 1.2 R8 6000 3200 4000 1400 1.6 4 4500 2500 3000 1100 1.6 4 1200 300 800 130 0.8 1.6 R10 4800 3000 3200 1300 2.0 5 3600 2300 2400 1000 2.0 5 1000 250 640 100 1.0 S2 When cutting austenitic stainless steel, the use of water-soluble cutting fluid is effective. If the depth of cut is shallow, the revolution and feed rate can be increased. The irregular helix flute end mill has a larger effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. a is the inclination angle of the machined surface. 978 Mitsubishi Materials