558 Каталог KYOCERA 2019 Режущий инструмент для металлообработки на станках Стр.H20

Каталог KYOCERA 2019 Режущий инструмент по металлу Стр. H20 0558 Lab2u

CUT-OFF CUT-OFF TOOLHOLDERS Small Diameter KGD (for Small Parts Machining) Insert Width: 0.059" 0.157" /1.3mm 4.0mm Toolholder Dimensions (Inch Size) Part Number Stock Cut-Off Dia. Dimensions (in) Angle n Insert Width CW (in) Spare Parts Clamp Bolt Wrench R L CUTDIA H HF HBH B LF LH WF GAMP MIN MAX u r KGDr/l 6-1.5JX 0.787 0.375 0.375 0.098 0.375 4.75 0.709 0.351 - 0.059 SB-40120TR LTW-15S 8-1.5JX 0.944 0.500 0.500 0.051 0.500 4.75 0.768 0.476 KGDr/l 6-2JX 0.787 0.375 0.375 0.098 0.375 4.75 0.709 0.342 0.079 0.118 8-2JX 0.944 0.500 0.500 0.051 0.500 4.75 0.768 0.467 1 0-2JX 1.259 0.625 0.625 - 0.625 4.75 0.965 0.592 KGDr/l 6-2.4JX 0.787 0.375 0.375 0.098 0.375 4.75 0.709 0.336 0.094 0.118 8-2.4JX 0.944 0.500 0.500 0.051 0.500 4.75 0.768 0.461 1 0-2.4JX 1.259 0.625 0.625 - 0.625 4.75 0.965 0.586 KGDr/l 8-3JX 0.944 0.500 0.500 0.051 0.500 4.75 0.768 0.453 0.118 0.118 1 0-3JX 1.259 0.625 0.625 - 0.625 4.75 0.965 0.578 0.157 KGDr/l 1 0-3D38JX 1.496 0.625 0.625 - 0.625 4.75 1.142 0.578 0.118 0.157 SE-50125TR LTW-20 1 2-3D42JX 1.653 0.750 0.750 - 0.750 4.75 1.220 0.703 43-3D42JX 1.653 0.750 0.750 - 0.500 4.75 1.220 0.453 Toolholder Dimensions (Metric Size) Part Number Stock Cut-Off Dia. Dimensions (mm) Angle n Insert Width CW (mm) Spare Parts Clamp Bolt/Screw Wrench R L CUTDIA H HF HBH B LF LH WF GAMP MIN MAX M 1h KGDr/l 101 OJX-1.3D16 16 10 10 2 10 120 18.0 9.9 5° 1.3 1.3 SB-40120TR LTW-15S 101 OJX-1.3 20 10 10 2 10 120 18.0 9.5 1212F-1.3D16 16 12 12 2 12 85 19.5 11.9 1212JX-1.3D16 16 12 12 2 12 120 19.5 11.9 1212F-1.3 24 12 12 2 12 85 19.5 11.5 1212JX-1.3 24 12 12 2 12 120 19.5 11.5 KGD% 101 OJX-1.5D16 16 10 10 2 10 120 18.0 9.7 5° 1.5 1.5 SB-40120TR LTW-15S 101 OJX-1.5 20 10 10 2 10 120 18.0 9.4 1212F-1.5D16 16 12 12 2 12 85 19.5 11.7 1212JX-1.5D16 16 12 12 2 12 120 19.5 11.7 121 2F-1.5 24 12 12 2 12 85 19.5 11.4 1212JX-1.5 24 12 12 2 12 120 19.5 11.4 KGD% 101 OJX-2 20 10 10 2 10 120 18.0 9.2 1° 2.0 3.0 SB-40120TR LTW-15S 1212F-2 24 12 12 2 12 85 19.5 11.2 1212JX-2 24 12 12 2 12 120 19.5 11.2 1616JX-2 32 16 16 - 16 120 24.5 15.2 2012K-2D34 34 20 20 - 12 125 32.5 11.2 0° HH5X16 LW-4 2020K-2D34 34 20 20 - 20 125 32.5 19.2 KGDr/l 101 OJX-2.4 20 10 10 2 10 120 18.0 9.0 1° 2.4 3.0 SB-40120TR LTW-15S 121 2F-2.4 24 12 12 2 12 85 19.5 11.0 121 2JX-2.4 24 12 12 2 12 120 19.5 11.0 161 6JX-2.4 32 16 16 - 16 120 24.5 15.0 2012K-2.4D34 34 20 20 - 12 125 32.5 11 0° HH5X16 LW-4 2020K-2.4D34 34 20 20 - 20 125 32.5 19 KGD% 1212JX-3 24 12 12 2 12 120 19.5 10.8 1° 3.0 3.0 SB-40120TR LTW-15S 1616JX-3 32 16 16 - 16 120 24.5 14.8 4.0 1616JX-3D38 38 16 16 - 16 120 29.0 14.8 1° 3.0 4.0 SE-50125TR LTW- 20 1913K-3D38 38 19 19 - 13 125 29.0 11.8 2012JX-3D42 42 20 20 - 12 120 31.0 10.8 2012JX-3D51 51 20 20 - 12 120 36.0 10.8 2020JX-3D42 42 20 20 - 20 120 31.0 18.8 2020JX-3D51 51 20 20 - 20 120 36.0 18.8 Note 1) 0.157" (4mm) width insert can be installed in KGDr/l8-3JX and KGDr/l1212JX-3, but is not recommended due to the toolholder's rigidity. 2) Recommended tightening torque for clamp screw is 2.0Nm for SB-40120TR and 2.5Nm for SE-50125TR. 3) When machining material greater than 01.417" (36mm) with KGDr/l...-3D38(JX), KGDr/l...-3D42(JX), or KGDr/l...-3D51 toolholders, use 1-edge inserts. Max. workpiece diameter for 2-edge inserts is 01.417" (36mm) Choose insert with width that falls within MIN and MAX parameters shown in table above. Insert table H18-H19 (Customer Service) - Option 1 H20 Kyocera (Technical Support) - Option 2 : Standard Item Zi : Phaseout Item (will be removed from next catalog) Visit us online at Contact your local Kyocera sales engineer to upgrade old products to new technology