436 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.436

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 436 0436 ENG Lab2u

Hoffmann Group 47 4asat M High feed rate indexable face mill Hi5 for milling inserts POMX 0704. Irregular spacing to minimise vibration. 3 0D/ number of teeth 2 mm 213200 0D3 ms L, 0D,h6 Pack of insert screws High feed rate milling cutter HI5 Weldon shank mm 25/2 208.89 10.6 1.4 36 92 25 219883 (10IP) 32/3 245.52 17.6 1.4 40 100 32 219883 (10IP) 40/4 274.23 25.6 1.4 50 110 32 219883 (10IP) 0D/ . number of teeth 213205 0D3 pmm 0D,h6 k 0D2 Mounting thread M Pack of insert screws High feed rate milling cutter 2 HI5 mm with thread mm 25/2 197.01 10.6 1.4 12.5 35 21 M12 219883 (10IP) 32/3 232.65 17.6 1.4 17 43 29 M16 219883 (10IP) 40/4 259.38 25.6 1.4 17 43 29 M16 219883 (10IP) 0D/ . number of teeth 213210 0D3 pmax I Mounting bore0 Pack of insert screws High feed rate milling cutter 2 HI5 mm with here mm 40/4 259.38 25.6 1.4 40 16 219884 (10IP) 50/5 290.07 35.6 1.4 40 22 219884 (10IP) 52/5 294.03 37.6 1.4 40 22 219884 (10IP) 63/6 320.76 48.6 1.4 50 27 219884 (10IP) 66/6 329.67 51.6 1.4 50 27 219884 (10IP) xiaGaiant Milling inserts for high feed rate indexable face mill No. 213200-213210 Good surface finishes are obtained due to flat cutting edges. 213137/3144- Preferred solution for difficult applications (interrupted cutting). Note: 0 Standard application values for a, = 0.5 ... 1xD/a =1.4mm. a,/D 0,5... 1,0 0,3 0,1 Correction factor f, 1 1,4 2,2 Suitable for/ Alu i Alu v( m/min >i s dc <500N DC <750N DC < SOON DC < 1100 N X <1400 N X <55 HRC X < 60 HRC X <65 HRC X <67 HRC X <70 HRC INOX <900 N INOX >900N Ti >850N GG(G) Graphite GRP CRP 6 i ISO code P H K N 213122 350 300 280 280 O 213125 T 420 400 380 330 213128/3144 1 360 310 260 200 170 130 2131311 T 50 40 35 30 300 213134/31411 T 360 320 280 180 150 80 o 2131371 150 120 70 o Type ST900 ST1400 HART INOX HB9530 10.08 10 £213125 POMX0704ZEERM HB9525 10.08 10 £213128 HB9540 - 10.08 - 10 £213131 POMX 0704ZESR R HB9715 10.08 10 £213134 pH MY M HB9640 - 10.08 - 10 £213137 rUIVlA U/u4ZllK IV1 HB9645 - 10.08 - 10 £213141 PAMY n7HA7PFD II HB9640 10.08 10 £213144 rUIVlA U/U4tLLn U HB9540 10.08 10 Programming radius at a... mm 3.61 f, mm 1 0.9 0.5 0.9 7 _ST900 _HART JJNI ifenarant Application instructions for high feed rate indexable face mills Hi5 No. 213200 - 213210 Milling cutter 0D Circular plunginc (interpolation) Oblique plunging (ramping Ramp angle o Ram p distance L mm degrees mm 25 38,5 47,5 26,7 3,0 32 52,5 61,5 13,9 6,2 40 68,5 77,5 9,0 9,5 50 88,5 97,5 6,2 14,2 52 92,5 101,5 5,8 15,3 63 114,5 123,5 4,3 20,5 66 120,5 129,5 4,1 21,5 0Dmip 436