194 Каталог HOFFMANN GROUP 2016 Станочный режущий и вспомогательный инструмент Вер. 47 Стр.194

Каталог HOFFMANN GROUP 2016 Режущий инструмент и оснастка Стр. 194 0194 ENG Lab2u

Hoffmann Group 47 M-LH 60‘ Solid carbide DIN 13 h6 DIN 6535 HA S2xD VvvVv bBaiant Micro-grain solid carbide single tooth thread milling cutter Corrected thread profile for milling exact internal threads (ensure stable clamping conditions). Very sturdy single-tooth thread mill, highly suitable especially for GRP, CRP, and graphite. Also suitable for Ti-based and Ni-based alloys and hardened steels up to 63 HRC. Advantage: Significantly less radial pressure than with multi-tooth thread mills. Note: Single-tooth thread mill exclusively for milling internal threads. The tapping hole (and where necessary the countersinking) has to be prepared beforehand 139610 Suitable for/ v, m/min Alu plastics qn£L, Alu cast > 10% Si X < 500 N X < 750 N X <900N X < 1100 N X <1400 N X <55 HRC X < 60 HRC X <67 HRC IN0X <900N INOX >900N Ti >850 N GRP CRP Graphite Uni 4 i 4k k ISO code N m- bn P H mi mi nrl 139610 300 300 200 300 250 200 100 80 60 40 30 100 80 60 100 100 150 139610 Single tooth thread mill 2xD TiAIN 139.10 139.10 129.20 124.25 120.78 120.78 120.78 120.78 120.78 139.59 139.59 139.59 J 1 f J \ No. of teeth Z X CRP I < 1400N mm 0.25 0.25 0.3 0.35 0.35 0.4 0.45 0.5 0.6 0.7 0.8 1 1, mm 0.74 0.9 1 1.2 1.35 1.5 1.9 2.4 2.8 3.2 4.1 4.9 mm 3 3.5 3.5 4 4 4 6 6 6 8 9 9 k mm 28 28 28 mm 32 32 32 32 32 32 32 32 32 40 40 40 mm 3 3 3 3 3 3 3 3 3 5 5 5 f, f, mm 0.01 0.02 0.01 0.02 0.01 0.02 0.01 0.02 0.01 0.02 0.01 0.02 0.01 0.02 0.01 0.02 0.01 0.02 0.02 0.04 0.028 0.05 0.035 0.06 M-LH 60" Solid carbide DIN 13 wl DIN 6535 HA 1 LJ <3xD Micro-grain solid carbide single tooth thread milling cutter with 1C Corrected thread profile for milling exact internal threads (ensure stable clamping conditions). Very sturdy single-tooth thread mill, highly suitable especially for GRP, CRP, and graphite. Also suitable for Ti-based and Ni-based alloys and hardened steels up to 58 HRC. Through-coolant feed a M8. Advantage: Significantly less radial pressure than with multi-tooth thread mills. Note: Single-tooth thread mill exclusively for milling internal threads. The tapping hole (and where necessary the countersinking) has to be prepared beforehand Because of the tooth profile only the thread nominal 0 (= size) with the corresponding thread pitch (see table) may be generated. 139615 Suitable for/ v, m/min Alu plastics omu Alu <%ra Alu cast > 10 % SI X < 500 N X < 750 N X <900N X < 1100 N X <1400 N X <55 HRC X <60 HRC X <65 HRC INOX <900N INOX >90011 Ti >850 N GRP CRP Graphite Uni 4 i 4k iC ISO code N m- INI P H mi mi mi 139615 300 300 200 200 150 120 80 60 50 30 80 60 50 100 100 150 139615 Single tooth thread mill 3xD TiAIN 149.49 144.54 134.15 134.15 134.15 163.85 169.29 169.29 204.93 241.56 241.56 356.40 402.93 mm 0.7 1.18 1.52 I.96 2.4 3.15 4.04 4.8 6.5 8.2 9.9 II.6 13.6 i, mm 3 4.8 6 7.5 9 12 15 18 24 31.5 37.7 42 48 I mm 28 28 28 28 28 28 36 36 36 40 40 45 45 m I mm 39 39 39 39 41 44 56 59 65 77 82 94 100 No. of teeth Z CRP f. f, mm 0.01 0.02 0.01 0.02 0.01 0.02 0.01 0.02 0.01 0.02 0.02 0.04 0.028 0.05 0.035 0.06 0.04 0.08 0.04 0.08 0.08 0.16 0.08 0.16 0.08 0.16 194