559 Каталог HOFFMANN GROUP 2016 Производственная мебель для работы и хранения Вер. 47 Стр.559

Каталог HOFFMANN GROUP 2016 Производственная мебель Стр. 559 0559 ENG Lab2u

Care instructions / servicing D Surfaces Powder-coated surfaces Powder-coated surfaces such as on workbenches, cabinets, and garment lockers should be cleaned with a cloth soaked with luke-warm water, to which neutral to mildly alkali cleaning agents may be added. Greasy, oily or rusty residues, and residues of adhesives, silicone rubber or adhesive tapes can be removed without trouble using white spirit or isopropyl alcohol. Always take care to use only non-abrasive cloths or cleaning agents. Never use corrosive materials, scouring agents, solvents, halogenated hydrocarbons or the like for cleaning. Plastic surfaces Plastic surfaces lack pores, so dirt does not easily adhere to them. Dusty parts should always be wiped over with a damp cloth, since a dry cloth can cause abrasion. A wet cloth also avoids generating static charges, which then attract still more dust. Mild soap or detergent in luke-warm water, applied with a soft sponge, cloth or washleather, should be used for cleaning them. If wet cleaning is not practical, the surface should be wiped down with a damp doth or washleather (without scouring). Commercially-available foam cleaners can also be used. The professional foam cleaner for stainless steel No. 083024 from the Hoffmann Group is particularly suitable. Please use commercially-available glass cleaners for cleaning polycarbonate windows. The TFT / LCD screen cleaner article 083026 and the cleaning cloth No. 089190 size Yellow from the Hoffmann Group are particularly suitable. Under no circumstances use abrasive cleaners, sharp cleaners, (degreased) wash-out agents, spray cleaners for glass, scouring cloths or brushes. Solvents such as acetone, carbon tetrachloride, paint thinners, or alcohol compounds containing more than 5% alcohol can attack the surface. Worktops Wood or bamboo Wood and bamboo are natural materials which are affected by the ambient temperature and humidity. To prevent the penetration of humidity and to restore the natural grain and colour of the material, you can treat unvarished worktops with our cleaner and care oil set No. 933659. Please only wipe over varnished worktops with a moist cloth. Avoid extreme temperatures, high humidity, and aggressive cleaning agents. Eluplan / Eterlux If only slightly dirty, wet cleaning is recommended, with a neutral or alcohol-based detergent added to the wiping water. When selecting cleaning and care media, make sure that the pH value is no higher than a maximum of 9. Please do not use any abrasive cleaning agents If very dirty, the use of basic cleaners or combined cleaning and care media is recommended. Apply them over the entire worktop or just part of it, and allow them to take effect for a few minutes. Using a cleaning pad suitable for linoleum, apply light mechanical pressure to release the dirt and then wipe off the wet surface until it is dry. Workplace mats and wooden safety slatting Wooden slatting Please regularly roll up the wooden safety slatting and stand it upright so that swarf and other dirt can fall off it. Regularly brush the ground under the wooden safety slatting, and as necessary brush down the wooden safety slatting or clean it with a steam jet. Please always allow the wooden safety slatting to dry thoroughly (standing upright). The wooden safety slatting should never be allowed to stand in water for long periods. Regularly wipe off oil or cooling lubricant emulsion (risk of slipping). Where necessary use detergents to remove grease. Rubber mats / PVC mats / nitrile rubber mats Use a high-pressure cleaner (maximum 124 bar) with warm water (not hotter than 70°C), especially if oil has to be removed. In addition the use of mild soap or detergent is recommended to improve the results. Mats with grid / anti-slip coating should not be cleaned using high-pressure jets. In dry areas, it is sufficient to brush them down. Vinyl foam mats The surface and the underside should be brushed down regularly or wiped down dry. The surface can additionally be wiped down damp with a mild detergent. Runners Regularly brush down or vacuum the surface. A wet mop with mild soap can be used. ESD mats It is important to brush the surface regularly or wipe it down dry. Additionally, we recommend the use of a detergent suitable for ESD, but a wet absorbent material with mild soap which leaves no residues can also be used. Other Mechanical components All moving parts such as hinges, slides, wheel bearings or rollers and locks retain their freedom of movement only if they are moistened occasionally with sprayed oil (such as No. 083044 Ballistol multi-function oil spray). On trucks, pay particular attention to rollers and axles. Threads or scraps of fabric can clog the rollers. Rigid foam inlays Please wash rigid foam inlays under running water. Washing-up liquid may be added, since this dissolves oil and grease and does not attack the material. The temperature must not exceed 75 °C. Under no circumstances use solvents. 559