High feed rate indexable face mill Garant for milling inserts POMX 10T5 Description Powerful and smooth-cutting high feed rate indexable face mil

High feed rate indexable face mill Garant for milling inserts POMX 10T5 Description Powerful and smooth-cutting high feed rate indexable face mill. Cost-efficiency due to 5-edge inserts. Ramping angle up to 10°. Version Unequal cutter pitch to minimise vibration. 0 D 3 0 D/ number of teeth mm 213110 I J&GMlt' I Hi5 high feed rate indexable face mill with bore 0D3 mm ap max mm Uot mm Mounting bore 0 mm Pack of insert screws 50/4 30.6 2.2 40 22 21 9889 (201P, 5.7 Nm) 52/4 32.6 2.2 40 22 21 9889 (201P, 5.7 Nm) 63/5 43.6 2.2 40 27 21 9889 (201P, 5.7 Nm) 66/5 46.6 2.2 50 27 21 9889 (20IP, 5.7 Nm) 80/6 60.6 2.2 50 32 21 9889 (20IP, 5.7 Nm) Garant Milling inserts for high feed rate indexable face mill No. 213110 Version Sturdy insert type (thickness 5.9 mm). Particularly cost-efficient due to 5 cutting edges. Good surface finishes are obtained due to projecting flat cutting edges. Positive high feed rate geometry. 21 3184/3193- Preferred solution for difficult applications (interrupted cutting). Note Standard application values for ae 0.5...1xD/ap max 2.2 mm. ae/D 0.5...1.0 0.3 0.1 Correction factor fz 1 1.4 2.2 Suitable for/ vc m/min Alu plastics osa&c Alu cast >10% Si <500 N <750 N <900 N 1 ’“ft' <1100N 1 sff' <1400 N j 2E INOX <900 N INOX >900 N Ti >850 N GG(G) CuZn I Uni es’ max min Air ISO code N P H K N 1 1 21 3166- 320 280 250 21 3169- 395 330 280 21 3172 - 275 250 o 21 3178- 80 50 30 300 21 3181 - 180 135 85 21 3184- 155 130 70 21 3190 - 340 320 270 170 125 75 290 21 3193 - 300 260 230 250 230 145 130 60 250 21 3166 213181 21 3190 Type ST900 ST1400 HART INOX UNI 21 3166 HB 9530 10 S 21 3169 POMX 10T5ZEER M HB 9525 10 21 3172 HB 9540 10 21 3178 POMX 10T5ZESR R HB 9715 10 21 3181 HB 9640 10 21 3184 HB 9645 10 21 3190 HB 9640 10 21 3193 HB 9540 10 Programming radius at aD max. mm 4.5 4.5 4.5 4.5 4.5 fz mm 1.25 1.1 0.7 1.1 /bjian j Application notes for Hi5 high feed rate indexable face mill No. 213110 Milling cutter 0D mm Circular plunge (Interpolation) Angled plunge (ramping) Dmln mm Dmax mm Ramp angle a degrees Ramp distance L mm 50 84.6 97.7 10.0 12.5 52 88.6 101.7 9.4 13.3 63 110.6 123.7 6.7 18.6 66 116.6 129.7 6.2 20.2 80 144.6 157.7 4.8 26.4 0 D m Main catalogue Hoffmann Group 46 393