Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS

Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi Materials по металлу SOLID END MILLS _ VFFDRB Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Side milling Work material Carbon steel, Alloy steel (180 280HB) Alloy tool steel (<350HB) Mild steel (<180HB) AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel (35 45HRC) AISI P21, AISI P20, AISI 4340, SKD, SKT Dii Cling pal Rmiuticr Feed per Tooth Table Feed Depth of at Depli of ait Cling feed Revolutior Feed per Tooth Table Feed Depth of cut Depth of cut DCH (mMi (min-1) (mloottil (mmlmin) ap(mr eeM (mtain (mirr1) ( tooth (mmtnin ipH 3 150 16000 0.15 9600 0.12 1.5 135 14000 0.15 8400 0.12 1.5 4 150 12000 0.20 9600 0.16 2.0 135 11000 0.20 8800 0.16 2.0 6 150 8000 0.35 11000 0.24 3.0 135 7200 0.35 10000 0.24 3.0 8 150 6000 0.35 13000 0.32 4.8 135 5400 0.35 11000 0.32 4.8 10 150 4800 0.40 12000 0.40 6.0 135 4300 0.40 10000 0.40 6.0 12 150 4000 0.45 11000 0.48 7.2 135 3600 0.45 9700 0.48 7.2 Work material Hardened steel (40 55HRC), Ferritic and Martensitic stainless steel (>200HB), Precipitation hardening stainless steel (<450HB) AISI H13, AISI L6, AISI 431, AISI 420,15-5PH, 17-4PH Hardened steel (55 62HRC) AISI D2 Dii Cutting spud Rovdutim Feed per Tooth Table Feed Depth of at Depth of cut Cling speed Revolution Feed per Tooth Table Feed Depth of at Depth of out DCH (mtiin (min-1) (mltoottil (itimlminl ap(mr ae(mm (mtain (mirr1) ( tooth (mtnin ap nm) ae(m 3 120 13000 0.15 7800 0.12 1.5 80 8500 0.10 3400 0.12 1.5 4 120 9500 0.21 8000 0.16 2.0 80 6400 0.15 3800 0.16 2.0 6 120 6400 0.35 9000 0.24 3.0 80 4200 0.30 5000 0.24 3.0 8 120 4800 0.35 10000 0.32 4.8 80 3200 0.30 5800 0.32 4.8 10 120 3800 0.40 9100 0.40 6.0 80 2500 0.35 5300 0.40 6.0 12 120 3200 0.45 8600 0.48 7.2 80 2100 0.40 5000 0.48 7.2 When ramping process set the feed rate at 50%. A ramping angle of 1 ° is recommended. Use at a revolution of 70% and feed rate of 50% when the tool overhang exceeds 5DC. 1024 Mitsubishi Materials