1588 Каталог MITSUBISHI 2020 Режущий инструмент Фрезы Резцы Сверла Пластины Стр.P132

Каталог MITSUBISHI 2020 Режущий инструмент для станков Стр. P132 1588 Lab2u

DRILLING(SOLID carbide) MGS SOLID GUN DRILL RECOMMENDED CUTTING CONDITIONS Work Mild Steel (5180HB) Carbon Steel, Alloy Steel (180 280HB) Material AIS11010 etc AIS11045, AISI 4140 etc Recommended grinding fluid Water insoluble Water insoluble Dia. DC (mm) Cutting Speed (m/min) Revolution (min'1) Feed rate (Min. Max.) (mm/rev) Table Feed (mm/min) Cutting Speed (m/min) Revolution (min'1) Feed rate (Min. Max.) (mm/rev) Table Feed (mm/min) 0.8 50 19800 0.01 (0.005-0.016) 195 40 15900 0.01 (0.005-0.016) 155 1.0 50 15900 0.01 (0.007-0.020) 155 40 12700 0.01 (0.007-0.020) 125 1.2 60 15900 0.015 (0.008-0.024) 235 50 13200 0.015 (0.008-0.024) 195 1.6 60 11900 0.02 (0.011-0.032) 235 50 9900 0.02 (0.011-0.032) 195 2.0 60 9500 0.025 (0.013-0.040) 235 50 7900 0.025 (0.013-0.040) 195 2.5 70 8900 0.03 (0.017-0.050) 265 60 7600 0.03 (0.017-0.050) 225 3.0 70 7400 0.04 (0.020-0.060) 295 60 6300 0.04 (0.020-0.060) 250 Work Carbon Steel, Alloy Steel (280 350HB) Austenitic Stainless Steel ( 200HB) Material AISI 4340 etc AISI 304, AISI 316 etc Recommended grinding fluid Water Insoluble Water Insoluble Dia. DC (mm) Cutting Speed (m/min) Revolution (min'1) Feed rate (Min. Max.) (mm/rev) Table Feed (mm/min) Cutting Speed (m/min) Revolution (min'1) Feed rate (Min. Max.) (mm/rev) Table Feed (mm/min) 0.8 30 11900 0.005 (0.004-0.005) 55 30 11900 0.01 (0.005-0.016) 115 1.0 30 9500 0.005 (0.005-0.007) 45 30 9500 0.01 (0.007-0.020) 95 1.2 40 10600 0.005 (0.006-0.008) 50 30 7900 0.015 (0.008-0.024) 115 1.6 40 7900 0.01 (0.008-0.011) 75 40 7900 0.02 (0.011-0.032) 155 2.0 40 6300 0.01 (0.010-0.013) 60 40 6300 0.025 (0.013-0.040) 155 2.5 50 6300 0.015 (0.013-0.017) 90 40 5000 0.03 (0.017-0.050) 150 3.0 50 5300 0.015 (0.015-0.020) 75 40 4200 0.04 (0.020-0.060) 165 Work Material Gray Cast Iron ( 350MPa) No 45 B etc Ductile Cast Iron ( 450MPa) 60-40-8 etc Recommended grinding fluid Water insoluble Water soluble Water insoluble Water soluble Dia. DC (mm) Cutting Speed Revolution Feed rate (Min. Max.) (mm/rev) Table Feed Cutting Speed Revolution Feed rate (Min. Max.) (mm/rev) Table Feed (m/min) (min'1) (mm/min) (m/min) (min'1) (mm/min) 0.8 50 19800 0.01 (0.008-0.016) 195 40 15900 0.005 (0.005-0.008) 75 1.0 50 15900 0.015 (0.010-0.020) 235 40 12700 0.005 (0.007-0.010) 60 1.2 60 15900 0.015 (0.012-0.024) 235 50 13200 0.01 (0.008-0.012) 130 1.6 60 11900 0.02 (0.016-0.032) 235 50 9900 0.01 (0.011-0.016) 95 2.0 60 9500 0.03 (0.020-0.040) 285 50 7900 0.015 (0.013-0.020) 115 2.5 70 8900 0.035 (0.025-0.050) 310 60 7600 0.02 (0.017-0.025) 150 3.0 70 7400 0.045 (0.030-0.060) 330 60 6300 0.025 (0.020-0.030) 155 Work Material Aluminium Alloy (Si<5%) Copper, Copper alloy Recommended grinding fluid Water insoluble Water soluble Water insoluble Water soluble Dia. DC (mm) Cutting Speed Revolution Feed rate (Min. Max.) (mm/rev) Table Feed Cutting Speed Revolution Feed rate (Min. Max.) (mm/rev) Table Feed (m/mln) (min'1) (mm/min) (m/mln) (min'1) (mm/min) 0.8 50 19800 0.01 (0.008-0.016) 195 40 15900 0.01 (0.008-0.016) 155 1.0 60 19000 0.015 (0.010-0.020) 285 50 15900 0.015 (0.010-0.020) 235 1.2 70 18500 0.015 (0.012-0.024) 275 60 15900 0.015 (0.012-0.024) 235 1.6 80 15900 0.02 (0.016-0.032) 315 70 13900 0.02 (0.016-0.032) 275 2.0 90 14300 0.03 (0.020-0.040) 425 80 12700 0.03 (0.020-0.040) 380 2.5 100 12700 0.035 (0.025-0.050) 440 90 11400 0.035 (0.025-0.050) 395 3.0 100 10600 0.045 (0.030-0.060) 475 100 10600 0.045 (0.030-0.060) 475 Note 1) For safety and success, high pressure coolant is required. (Minimum coolant pressures ,000PSI) Note 2) Coolant filter must be less than 5 microns. Fine filtration is necessary to prevent blockage of the coolant holes. Note 3) A pilot hole or guide bushing is required.